00198500-02_VD_711.1_R18-1_DE_EN.pdf - 第36页
Station Software 71 1.1 (R18 - 1) / Versio n Description 05/2018 Edition 36 10 Important Terms and Abbrev iations CA4 CA4 V2 Machine type of the Chip Assembly (CA ) - series with 4 g antries and 2 PAs C&P Collect &am…
Station Software 711.1 (R18-1) / Version Description 05/2018 Edition
35
D1-142505101 The software hung up and had to be restarted.
D1-142515201 CA4: When the mapping ACT was performed, the fiducials were measured
only with the master gantry. There was no dual gantry transformation.
D1-142536004 The station software hung up when the user level was changed.
D1-142624049 When a carrier X was set up, the station reported feeder missing;
pickup not possible
.
D1-142673101 The Skip recognition button was active on the basic production level. The
activity level could be changed now.
D17915-12902 The first component was not picked up after feeder error.
D18317-2201 The machine stopped during production without any error message.
D18164-10301 Omitted tracks were reset when the setup was changed, but not when the
same job was downloaded again. A job download should also activate the
track.
Table 9-7: Corrected errors station software version 710.1 Patch 2
710.1 Patch 1
Error no. Error description
D1-130023341 The measurement of cycle time did not work for some configurations.
D1-140150945 Confirming the exchange of a cassette did not set the levels full.
D1-140532401 LED-Centering: the glass plate was worn out too fast.
D1-140754501 After a reboot after a virus scan, the software did not start any longer.
D1-140811309 After a partial download, all feeder LEDs were on until the table was taken out
and in again.
D1-141145401 It was not possible to download an accuracy of 25µm for SST45.
D17754-11401 Gantry 2 waited for gantry 3 several cycles before it started to place.
D18224-30501 A board in lane 2 was placed only when lane 1 got empty. The reason was a
safety distance which is needed when a high component is placed on the side
of the CPP gantry. This distance value was slightly too high.
Table 9-8: Corrected errors station software version 710.1 Patch 1
Station Software 711.1 (R18-1) / Version Description 05/2018 Edition
36
10 Important Terms and Abbreviations
CA4
CA4 V2
Machine type of the Chip Assembly (CA)-series with 4 gantries
and 2 PAs
C&P Collect & Place
CPP Collect & Place & Pick & Place
DC Dual Conveyor
DX1/DX2 Machine type with 1 or 2 gantries and 1 PA
EDIF Electronic Design Interchange Format
eWLP embedded Wafer Level Process
FOPLP Fan-Out Panel Level Packaging
FCCS Field Camera Calibration System
GUI Graphical User Interface
HFH High Force Head
HW Hardware
MGCU Modular Gantry Control Unit
MHCU Modular Head Control Unit
MTC Matrix Tray Changer
OIS Operator Information System
PA Processing area
PCB Printed circuit board
Placement mode:
2-in-1
When a machine runs in I-Placement mode, it is possible to
perform manual operations for one side / gantry. This placement
mode is also called "independent".
Placement mode:
Alternating
Placement mode in a dual gantry placement area, in which both
gantries place components on both boards in a dual conveyor.
First, both gantries place all assigned components on the board
in lane one and then on the board in lane two.
Placement mode:
Borrow
Performance
A line runs in I-Placement mode and to get a balanced
throughput between the left and right conveyor lanes, e.g. the
last machine runs in Alternating mode and places components in
this placement area on the board of the other lane.
Placement mode:
I-Placement
Placement mode in a dual gantry placement area in which each
gantry only places components on the board of the assigned
conveyor lane.
SC Single Conveyor
SC SIPLACE Setup Center (external setup control system)
SW Software
SWS SIPLACE Wafer System
SX1/SX2 Machine type with 1 or 2 gantries and 1 PA
TH Twin Head
TH HF Twin Head High Force
Station Software 711.1 (R18-1) / Version Description 05/2018 Edition
37
Twin VHF Very High Force Twin Head
TX1/TX2/TX2i Machine type with 1 or 2 gantries and 1 PA
TX1/TX2 V2
TX2i V2
Machine type with 1 or 2 gantries and 1 PA
TX2 micron/
TX2i micron
TX2i micron 15 µm
Machine type with 2 gantries and 1 PA
VC Vision computer
VCU Vision Control Unit
VHF P&P Very High Force Pick&Place
WLFO Wafer Level Fan-Out, Chip Assembly process
WPC Waffle Pack Changer
X2/X2 S Machine type with 2 gantries and 2 PAs
X3/X3 S Machine types with 3 gantries and 2 PAs
X4/X4 S/
X4 S micron
Machine types with 4 gantries and 2 PAs
X4i/X4i S
X4i S micron
Machine types with 4 gantries and 2 PAs