00196376-0102_UM S-Feeder_EN.pdf - 第42页
Tape Feeder Modules Details for 3x8 mm S Feeders Inserting the Tape Reel Holder 42 User Manual SIPLACE S-Feeder 2.2.4 Inserting the Tape Reel Holder When using 3x8 mm S feeders, the t apes to be processed are so clo se t…
Tape Feeder Modules
Setting the Step Size Details for 3x8 mm S Feeders
User Manual SIPLACE S-Feeder 41
2.2.3 Setting the Step Size
The 3x8 mm S feeders can be used with a step size of 2 mm, 4 mm or 8 mm (only for 3x8 mm S and
3x8 mm SL).
To set the step size, proceed as follows:
►Use the blue "Select" button to select the track for which you want to set the step size.
The selected track will be marked by a dot in the control unit display.
►(1) Press the green "Index" button and hold until the display begins to flash.
►(2) Hold the green "Index" button and, at the same time, press the yellow "Foil" button.
The step size will change each time you press the yellow button and will flash on the control unit
display.
►(3) Release the green "Index" button. The set step size will be shown permanently.
Tape Feeder Modules
Details for 3x8 mm S Feeders Inserting the Tape Reel Holder
42 User Manual SIPLACE S-Feeder
2.2.4 Inserting the Tape Reel Holder
When using 3x8 mm S feeders, the tapes to be processed are so close together that it is better not to
place the corresponding tape reels next to one another but instead in a staggered or offset arrangement.
The middle tape reel for each feeder is positioned slightly higher than the others, on a tape reel holder.
Each of these tape reel holders can accommodate one tape reel on the left and one on the right i.e. a
maximum of two tape reels. A deflection pulley keeps the tapes tensioned.
Example
You want to use four 3x8 mm S feeders next to one another.
In this case you will need 2 tape reel holders with deflection pulley.
▪ Tape reel holder A accommodates the middle tape from feeder 1 on its left and the middle tape from
feeder 2 on its right.
▪ Tape reel holder B accommodates the middle tape from feeder 3 on its left and the middle tape from
feeder 4 on its right.
2.2.4.1 Preparing the Middle Tape Reels
►(1) Take the middle tape reel of each feeder and place it higher up.
►(2) Insert the tape reel holder in each second space e.g. as shown on the photo at feeders 2 and 4
(A and B).
►(3) Make sure that the tape reel holder engages correctly into the rail.
►Now place the middle tape reels onto the sides of the tape reel holders.
Example:
Place the middle tape of feeder 1 onto the left of tape reel holder A and the middle tape of feeder 2
onto the right side of the same holder.
Place the middle tape of feeder 3 onto the left of tape reel holder B and the middle tape of feeder 4
onto the right side of this holder.
Tape Feeder Modules
Inserting the Tape Reel Holder Details for 3x8 mm S Feeders
User Manual SIPLACE S-Feeder 43
2.2.4.2 Inserting the Deflection Pulleys
The deflection pulleys keep the tapes tensioned in the tape reel holders.
►(1) Position the deflection pulley above the tape reel holder.
►(2) Insert the deflection pulley into the recess in the tape reel holder.
►(3) Take the deflection pulley by the handle and turn it in the direction of the arrow.
►(4) The diagram shows an example of an optimum setup.