Samsung（三星）-KLM8G1GEAC-B001.pdf - 第20页

- 19 - IF THERE IS ANY OTHER OPERATION TO IMPLEMENT IN ADDITION TO SPECIFICATION IN THE DATASHEET OR JEDEC STANDARD, PLEASE CONTACT EACH BRANCH OFFICE OR HEADQUARTERS OF SAMSUNG ELECTRONICS. datasheet e·MMC Rev. 1.0 KLMx…

- 18 -

IF THERE IS ANY OTHER OPERATION TO IMPLEMENT IN ADDITION TO SPECIFICATION

IN THE DATASHEET OR JEDEC STANDARD, PLEASE CONTACT EACH BRANCH OFFICE OR

HEADQUARTERS OF SAMSUNG ELECTRONICS.

datasheet

e·MMC

Rev. 1.0

KLMxGxGEAC-B001

SAMSUNG CONFIDENTIAL

5.1.4 Auto Power Saving Mode

If host does not issue any command during a certain duration (1ms), after previously issued command is completed, the device enters "Power Saving

mode" to reduce power consumption.

At this time, commands arriving at the device while it is in power saving mode will be serviced in normal fashion

[Table 27] Auto Power Saving Mode enter and exit

[Table 28] Auto Power Saving Mode and Sleep Mode

5.1.5 Performance

[Table 29] Performance

* Test / Estimation Condition : Bus width x8, 200MHz SDR, 512KB data transfer, w/o file system overhead

Mode Enter Condition Escape Condition

Auto Power Saving Mode

When previous operation which came from Host is completed and no command is issued dur-

ing a certain time.

If Host issues any command

Auto Power Saving Mode Sleep Mode

NAND Power ON OFF

GotoSleep Time < 1ms < 1ms

Density Sequential Read (MB/s) Sequential Write (MB/s)

8 GB 120 18

16 GB

150

32 GB

64 GB

- 19 -

IF THERE IS ANY OTHER OPERATION TO IMPLEMENT IN ADDITION TO SPECIFICATION

IN THE DATASHEET OR JEDEC STANDARD, PLEASE CONTACT EACH BRANCH OFFICE OR

HEADQUARTERS OF SAMSUNG ELECTRONICS.

datasheet

e·MMC

Rev. 1.0

KLMxGxGEAC-B001

SAMSUNG CONFIDENTIAL

6.0 REGISTER VALUE

6.1 OCR Register

The 32-bit operation conditions register stores the VDD voltage profile of the e·MMC. In addition, this register includes a status information bit. This status

bit is set if the e·MMC power up procedure has been finished. The OCR register shall be implemented by all e·MMCs.

[Table 30] OCR Register

NOTE :

1) This bit is set to LOW if the e·MMC has not finished the power up routine

2) The voltage for internal flash memory(VDDF) should be 2.7-3.6v regardless of OCR Register value.

6.2 CID Register

[Table 31] CID Register

NOTE :

1),4),5) description are same as e.MMC JEDEC standard

2) PRV is composed of the revision count of controller and the revision count of F/W patch

3) A 32 bits unsigned binary integer. (Random Number)

6.2.1 Product name table (In CID Register)

[Table 32] Product name table

OCR bit

VDD voltage window

[6:0] Reserved 00 00000b

[7] 1.70 - 1.95 1b

[14:8] 2.0-2.6 000 0000b

[23:15] 2.7-3.6 1 1111 1111b

[28:24] Reserved 0 0000b

[30:29] Access Mode 00b (byte mode) 10b (sector mode) -[ *Higher than 2GB only]

[31]

e·MMC power up status bit (busy)

Name Field Width CID-slice CID Value

Manufacturer ID MID 8 [127:120] 0x15

Reserved 6 [119:114] ---

Card/BGA CBX 2 [113:112] 01

OEM/Application ID OID 8 [111:104]

---

Product name PNM 48 [103:56] See Product name table

Product revision PRV 8 [55:48]

---

Product serial number PSN 32 [47:16]

---

Manufacturing date MDT 8 [15:8]

---

CRC7 checksum CRC 7 [7:1]

---

not used, always ’1’ - 1 [0:0] ---

Part Number Density Product Name in CID Register (PNM)

KLM8G1GEAC-B001 8 GB 0 x 4D3847314743

KLMAG2GEAC-B001 16 GB 0 x 4D4147324743

KLMBG4GEAC-B001 32 GB 0 x 4D4247344743

KLMCG8GEAC-B001 64 GB 0 x 4D4347384743

- 20 -

IF THERE IS ANY OTHER OPERATION TO IMPLEMENT IN ADDITION TO SPECIFICATION

IN THE DATASHEET OR JEDEC STANDARD, PLEASE CONTACT EACH BRANCH OFFICE OR

HEADQUARTERS OF SAMSUNG ELECTRONICS.

datasheet

e·MMC

Rev. 1.0

KLMxGxGEAC-B001

SAMSUNG CONFIDENTIAL

6.3 CSD Register

The Card-Specific Data register provides information on how to access the e·MMC contents. The CSD defines the data format, error correction type, max-

imum data access time, data transfer speed, whether the DSR register can be used etc. The programmable part of the register (entries marked by W or

E, see below) can be changed by CMD27. The type of the entries in the table below is coded as follows:

R : Read only

W: One time programmable and not readable.

R/W: One time programmable and readable.

W/E : Multiple writable with value kept after power failure, H/W reset assertion and any CMD0 reset and not readable.

R/W/E: Multiple writable with value kept after power failure, H/W reset assertion and any CMD0 reset and readable.

R/W/C_P: Writable after value cleared by power failure and HW/ rest assertion (the value not cleared by CMD0 reset) and readable.

R/W/E_P: Multiple writable with value reset after power failure, H/W reset assertion and any CMD0 reset and readable.

W/E/_P: Multiple wtitable with value reset after power failure, H/W reset assertion and any CMD0 reset and not readable.

[Table 33] CSD Register

Name Field Width Cell Type CSD-slice

CSD Value

8GB 16GB 32GB 64GB

CSD structure CSD_STRUCTURE 2 R [127:126] 0x03

System specification version SPEC_VERS 4 R [125:122] 0x04

Reserved - 2 R [121:120] -

Data read access-time 1 TAAC 8 R [119:112] 0x27

Data read access-time 2 in CLK cycles (NSAC*100) NSAC 8 R [111:104] 0x01

Max. bus clock frequency TRAN_SPEED 8 R [103:96] 0x32

Device command classes CCC 12 R [95:84] 0xF5

Max. read data block length READ_BL_LEN 4 R [83:80] 0x09

Partial blocks for read allowed READ_BL_PARTIAL 1 R [79:79] 0x00

Write block misalignment WRITE_BLK_MISALIGN 1 R [78:78] 0x00

Read block misalignment READ_BLK_MISALIGN 1 R [77:77] 0x00

DSR implemented DSR_IMP 1 R [76:76] 0x00

Reserved - 2 R [75:74] -

Device size C_SIZE 12 R [73:62] 0xFFF

Max. read current @ VDD min VDD_R_CURR_MIN 3 R [61:59] 0x06

Max. read current @ VDD max VDD_R_CURR_MAX 3 R [58:56] 0x06

Max. write current @ VDD min VDD_W_CURR_MIN 3 R [55:53] 0x06

Max. write current @ VDD max VDD_W_CURR_MAX 3 R [52:50] 0x06

Device size multiplier C_SIZE_MULT 3 R [49:47] 0x07

Erase group size ERASE_GRP_SIZE 5 R [46:42] 0x1F

Erase group size multiplier ERASE_GRP_MULT 5 R [41:37] 0x1F

Write protect group size WP_GRP_SIZE 5 R [36:32] 0x0F

Write protect group enable WP_GRP_ENABLE 1 R [31:31] 0x01

Manufacturer default ECC DEFAULT_ECC 2 R [30:29] 0x00

Write speed factor R2W_FACTOR 3 R [28:26] 0x03

Max. write data block length WRITE_BL_LEN 4 R [25:22] 0x09

Partial blocks for write allowed WRITE_BL_PARTIAL 1 R [21:21] 0x00

Reserved - 4 R [20:17] -

Content protection application CONTENT_PROT_APP 1 R [16:16] 0x00

File format group FILE_FORMAT_GRP 1 R/W [15:15] 0x00

Copy flag (OTP) COPY 1 R/W [14:14] 0x01

Permanent write protection PERM_WRITE_PROTECT 1 R/W [13:13] 0x00

Temporary write protection TMP_WRITE_PROTECT 1 R/W/E [12:12] 0x00

File format FILE_FORMAT 2 R/W [11:10] 0x00

ECC code ECC 2 R/W/E [9:8] 0x00

CRC CRC 7 R/W/E [7:1] -

Not used, always’1’ - 1 — [0:0] -