IPC 7711A.pdf - 第55页
OUTLINE This procedure covers epoxy mixing and handling. The epoxy covered by this pro- cedure has multiple uses including solder resist repair, base board repair, circuitry over-coating and delamination repair. NOTE For…
NOTES
IPC-7711A/7721A
Number: 2.5
Revision:
Date: 2/98
Subject: Baking and Preheating
Page2of2
Copyright Association Connecting Electronics Industries
Provided by IHS under license with IPC
Not for Resale
No reproduction or networking permitted without license from IHS
--``,``,-`-`,,`,,`,`,,`---
OUTLINE
This procedure covers epoxy mixing and handling. The epoxy covered by this pro-
cedure has multiple uses including solder resist repair, base board repair, circuitry
over-coating and delamination repair.
NOTE
For high strength or high temperature applications two part epoxies will generally
have the best properties.
REFERENCES
2.1 Handling Electronic Assemblies
2.2 Cleaning
2.5 Baking and Preheating
TOOLS AND MATERIALS
Balance/Scale
Cleaner
Color Agent, Various Colors
Epoxy
Foam Swab
Heat Lamp
Mixing Cup
Mixing Stick
Oven
Wipes
PRINTED WIRING BOARD PREPARATION
The area where the epoxy is to be applied should be prepared prior to mixing the
epoxy. This preparation may include preheating the affected area to improve absorp-
tion of the applied epoxy. The entire printed wiring board may also be heated in an
oven or with a heat lamp.
CAUTION
Some components may be sensitive to high temperatures.
CAUTION
Avoid skin contact with epoxy materials.
PROCEDURE - Prepackaged Two Part Epoxy
1. Remove the clip separating the resin and activator. Mix by squeezing both halves
together with your fingers. Mix for at least one minute to ensure a complete mix
of the resin and activator. (See Figure 1.)
2. Cut open one end of the epoxy tube and squeeze the contents into a mixing cup.
Mix again with a mixing stick to ensure a thorough mixture of the resin and acti-
vator.
Figure 1 Mix resin and activator
inside package of prepackaged epoxy.
Figure 2 Apply epoxy. Foam swab
may be used to add texture.
7711A/7721A
General
Information and
Common Procedures
Revision:
Date: 2/98
Epoxy Mixing
and Handling
Number: 2.6
Product Class: R, F, W, C
Skill Level: Intermediate
Level of Conformance: High
Material in this manual was voluntarily established by Technical Committees of IPC. This material is advisory only and its use
or adaptation is entirely voluntary. IPC disclaims all liability of any kind as to the use, application, or adaptation of this material.
Users are also wholly responsible for protecting themselves against all claims or liabilities for patent infringement. Equipment
referenced is for the convenience of the user and does not imply endorsement by IPC.
Page1of2
Copyright Association Connecting Electronics Industries
Provided by IHS under license with IPC
Not for Resale
No reproduction or networking permitted without license from IHS
--``,``,-`-`,,`,,`,`,,`---
NOTE
For bubble free epoxy, remove the clip separating the resin and activator. Cut
open one end of the Epoxy tube and squeeze the contents into a mixing cup.
Slowly stir the mixture with the mixing stick. Be sure to stir the mixture for at least
2 minutes to ensure that all the resin and actuator have completely mixed.
3. If needed, add color agent to the mixed epoxy. Stir slowly to prevent bubbles.
CAUTION
Be sure the color agent is compatible with the epoxy mixture.
4. Apply or use as needed. (See Figure 2.)
5. Cure the epoxy per the manufacturer’s recommendations.
EVALUATION
1. Visual examination of epoxy for texture and color match.
2. Testing of epoxy surface for complete cure.
3. Electrical tests as applicable.
NOTES
IPC-7711A/7721A
Number: 2.6
Revision:
Date: 2/98
Subject: Epoxy Mixing and Handling
Page2of2
Copyright Association Connecting Electronics Industries
Provided by IHS under license with IPC
Not for Resale
No reproduction or networking permitted without license from IHS
--``,``,-`-`,,`,,`,`,,`---