SME_DB_Feeder_User_Guide(Eng_Ver1.5) (1).pdf - 第78页
4-8 SM-Series SME DB Tape Feeder User's Manual Lift the tape guide to check the lower surface of the tape guid e and upper surfa ce of the main body visually [Measures] Clean the tape guide. E0004 Incorrect part…
4-7
Trouble Shooting
4.2.1.1. Part Non-pickup Error
E0000 Tape is not set properly in the tape feeder.
[Cause]
Sprocket teeth of the tape feeder are not engaged correctly into the tape holes.
[How to Check]
Check whether the sprocket is engaged into tape holes properly.
Check whether the tape reel is not set in the tape feeder with the cover tape not being
peeled off.
[Measures]
Engage the sprocket teeth of the tape feeder into the tape holes correctly.
E0001 Defect occurred to the tape
[Cause]
When removing the cover tape by hand, a part is detached along with the cover tape
since it is stuck on the cover tape.
[How to Check]
When removing the cover tape manually, check whether a part is lifted due to its being
stuck to the tape.
[Measures]
Change the tape
E0002 Tape guide is deformed
[Cause]
The tape guide does not move smoothly or it is deformed due to impact
[How to Check]
Check whether the tape guide moves smoothly by moving the tape guide. Then check
for its deformation.
[Measures]
Contact our designated C/S company or local agent.
(Replac
e the tape guide)
E0003 D
efective tape guide maintenance
[Cause]
Foreign material is jammed in the cover tape slot of the tape guide.
Foreign materials or parts such as chips are jammed between the tape guide and the
main body of the feeder or between the tape guide and tape.
[How to Check]
4-8
SM-Series SME DB Tape Feeder User's Manual
Lift the tape guide to check the lower surface of the tape guide and upper surface of
the main body visually
[Measures]
Clean the tape guide.
E0004 Incorrect part supply speed setup
[Cause]
The part to be supplied at low speed mode is supplied at high speed mode
[How to Check]
Check the part supply speed in the ‘Part’ menu of the MMI
[Measures]
Change the part supply speed to low speed mode in the ‘Part’ menu of the MMI.
E0005 Defective feeder maintenance
[Cause]
Foreign materials exist on the sprocket, which disturbs feeding
[How to Check]
Check for existence of foreign materials on the sprocket
[Measures]
Remove the foreign materials on the sprocket and ratchet
E0006 Defective feeding motor operation of the tape feeder
[Cause]
Abnormal power supply to the motor
The board (VCCB) in the docking cart is defective
The clamp dra
wer connector is defective
De
fective feeder motor
Defective contact of the interface connector
Noise is generated from the motor
Defective feeder control board
Defective feeder control board cable
[How to Check]
After checking whether 24V power is applied to the docking cart, check the
connection status of the VCCB cable and clamp drawer connector.
Install the tape again and check whether the homing and feeding of the feeder motor is
performed properly.
4-9
Trouble Shooting
Clean the feeder and feeder base slot interface connectors and check whether homing
and feeding are performed properly
Check whether feeder setup unit generates a noise during homing and feeding, and
check visually the degree of vibration of the sprocket gear when it stops after feeding
Replace the feeder control board and check whether it operates properly
Check whether the feeder board control board cable is properly connected. Replace the
feeder control board cable and check whether the board operates proplerly
[Measures]
Contact our designated C/S company or local agent
Remove the cause of overload. If there is any problem, contact our local agent
for proper measures.(Replace feeder motor)
Contact our designated C/S company or local agent. (Replace the interface
connector)
Contact our designated C/S company or local agent. (Replace the feeder motor)
Contact our designated C/S company or local agent. (Replac
e the feeder control
board
)
Contact our designated C/S company
or local agent. (Replac
e the feeder control
bo
ard cable)
E0007 Problem with accuracy
[Cause]
Y-axis distorted
[How to Check]
Y-axis precision distorted
[Measures]
Check the feeder for malfunctioning and loss rate using the MMI of the chip mounter.
E0008 Pickup Z setup error occurred.
[Cause]
Pickup height setup is incorrect.
[How to Check]
Check whether the Pickup Z value is appropriate for the corresponding part
[Measures]
Adjust the pickup Z height and pickup speed.
E0009 The down movement for pickup is fast.
[Cause]