SIPLACE D系列Servicemanual.pdf - 第50页
Service Wo rk Gantry D3 50 Servicemanual (internal ve rsion) SIPLACE D Series Prep aring the T railing Cable Handling and overview of gauge The trailing cable is supplied as a complete assembly. The pneumat ic hoses need…
Service Work
D3 Gantry
Servicemanual (internal version) SIPLACE D Series
49
The following auxiliary tools are included with trailing cable which have an S number:
Gauge for Trailing cable, gantry 1+3 X series [0038302901]
Gauge for Trailing cable, gantry 2+4 X series [0038305701]
Gauge for Trailing cable X4I [00383057-xx]
Edding marker, white [0038274001]
Press-fit connection QS-6 [0304977001]
In accordance with your machine's configuration,
you will need to remove the relevant modules,
covers and cover plates before you can dismantle
the trailing cable.
X Where necessary, remove the cover plates
from the gantry trailing cable. Mark their exact
position to ensure correct replacement later.
X Remove the top central cover from the
SIPLACE machine.
X Remove the upright covers over the trailing
interface gantry, so that you can reach the
trailing cable.
Service Work
Gantry D3
50 Servicemanual (internal version) SIPLACE D Series
Preparing the Trailing Cable
Handling and overview of gauge
The trailing cable is supplied as a complete
assembly.
The pneumatic hoses need to be shortened to the
exact length of the distance to the pneumatic
distributor on the head mount and in the machine.
Use the gauge to help you with this. The existing
pneumatic hoses, which are run in the machine,
need to be cut through and connected to the
trailing cable at the exact position, with the help of
hose couplings [03049770-01].
There are two gauges available, for the different
gantries.
Gauge for Trailing cable, gantry 1+3 X series
[0038302901]
Gauge for Trailing cable, gantry 2+4 X series
[0038305701]
Only for the rotated gantry 2+4 for SIPLACE
X4i:
Gauge for Trailing cable SIPLACE X4i 2P G
[03051596-01]
Legend
The gauges are labeled to ensure correct
handling.
1. Stopper edge for clamping X + Y: this side of
the gauge must be attached to the respective
trailing cable clamp.
2. Machine inside: This side of the gauge must
point to the inside of the machine.
3. Gauge designations
4. X hose: this is where you see the 7 drillings for
the X hose markings.
5. Y hose: this is where you see the 7 drillings for
the Y hose markings.
Service Work
D3 Gantry
Servicemanual (internal version) SIPLACE D Series
51
Shortening X hoses at the X trailing cable
clamp (to the pneumatic distributor at the
head mount)
1. Gauge for shortening the hoses
2. X trailing cable clamp
3. Stopper edge (gauge at clamp)
4. Hose marking
X Observe the designation for the respective
gantry on the gauge (1) (gantry 1+3 or gantry
2+4). Select the correct gauge.
X Place the stopper edge (3) of the gauge (see
mark labeled edge for clamp X+ Y on the
gauge) at the edge of the clamping plate (2) for
the X trailing cable.
X Mark the pneumatic hoses through the holes
(4) in the gauge. Observe the position labeled
X hose.
ATTENTION:
Mark the correct position!
X Observe the position labeled X hose.
X Observe the position marked
machine inside on the gauge.
X To ensure that they have the correct
length, cut the pneumatic hoses at
the marking labeled "X hose". If the
pneumatic hoses are cut too short,
you will have to discard the entire
trailing cable.
X Use the hose pliers to cut the pneumatic hoses
at the marked position. The pneumatic hoses
can now be run inside the pneumatic
distributor, with the correct curvature.