00198365-03_UM_JTF-ML2_TX12_V1-V2_EN.pdf - 第9页

1 Introduction 1.2 Important Notes about this Manual User Manual SIPLACE TX V1/V2 Series JEDEC Tray Feeder (JTF-ML2) 11/2019 9 1.1.7 Electromagnetic compatibility (EMC) All SIPLACE products are designed and tested for pr…

1 Introduction

1.1 Module description

8 User Manual SIPLACE TX V1/V2 Series JEDEC Tray Feeder (JTF-ML2) 11/2019

1.1.2 EU Declaration of Conformity

The product/device described below conforms to the regulations and standards listed in the EU

Declaration of Conformity provided.

Model JEDEC tray feeder

Type SIPLACE JTF-ML2

Item no.: 00588116- xx

Manufacturer:

ASM Assembly Systems Singapore Pte Ltd

535 Yishun Industrial Park A

ASM Tech-Park Building 2

Singapore 768775

1.1.3 Correct Usage

The product may only be used for the application cases described in the catalogues and technical

specifications i.e. for placement of SMD components and only in connection with the third party

devices and components recommended or approved by ASM Assembly Systems GmbH & Co. KG.

Any other use is deemed to be incorrect and not as prescribed.

If the product is not used as prescribed, ASM Assembly Systems GmbH & Co. KG will accept no

liability for any damage that may occur and will not guarantee that the components will work prop-

erly and without problems.

Prescribed or correct usage includes the observance of all the instructions in the user manual.

The proper and safe operation of the product requires correct transportation, storage, installation

and assembly, plus careful, accurate utilization and servicing.

1.1.4 Incorrect Usage

Failure to use the product as prescribed can result in both danger to life and limb and material

damage. For this reason, non-prescribed usage is prohibited. If the product is not used as pre-

scribed, ASM Assembly Systems GmbH & Co. KG will not accept liability for any damage that may

occur and will not guarantee that the components will work properly and without problems.

Non-prescribed use of the module includes the following examples:

●

Operation of the module with safety equipment deactivated or removed.

●

Placement of components that do not meet the permitted specification.

●

Use of unauthorized accessories and additional modules.

●

Use of the module by unqualified personnel.

1.1.5 Noise Emission Information

Max. noise emissions 75 dB (A)

1.1.6 Environmentally-friendly disposal of materials and components

Our products are manufactured using only materials and parts that can be easily separated and

disposed of in an environmentally-friendly way.

NOTICE

Observe the applicable regulations

The company operating the system has sole responsibility for the proper, environmentally-

friendly disposal of machines, working materials, consumable materials and wear parts.

► Please observe your national statutory provisions for waste disposal and environ-

mental protection.

1 Introduction

1.2 Important Notes about this Manual

User Manual SIPLACE TX V1/V2 Series JEDEC Tray Feeder (JTF-ML2) 11/2019 9

1.1.7 Electromagnetic compatibility (EMC)

All SIPLACE products are designed and tested for professional use in industrial applications.

Electromagnetic compatibility in terms of the emission of interference cannot be guaranteed in any

other environment.

1.1.8 Use of original accessories and spare parts

Only use original spare parts and authorized accessories. The use of other parts will affect safety

and will invalidate the liability for any consequential damage.

1.2 Important Notes about this Manual

1.2.1 Contents and Filing of this Manual

This User Manual contains basic information that must be observed when setting up, operating and

maintaining the machine. The service engineers, qualified staff, operators and users must therefore

read it before commencing installation and commissioning. The instructions must be kept perman-

ently accessible wherever the machine is used.

In addition, the user must ensure that the employees have fully understood the contents of the user

manual.

1.2.2 Danger notes

WARNING

Danger notes

► Work may only be performed on the JEDEC tray feeder if the personnel concerned

have a thorough knowledge of the relevant section of the user manual.

► All work must be carried out by appropriately trained and qualified personnel.

► All warnings, cautions and hazard notes must be observed.

► Carefully read through Chapter 2 on operational safety in the user manual for this pur-

pose.

1.2.3 Manufacturer's/supplier's liability

We draw your attention to the fact that these instructions only contain descriptive and explanatory

material and do not include any contractual conditions or undertakings. All obligations of ASM

Assembly Systems GmbH & Co. KG are conclusively specified in the respective contract, on the

basis of which you have received the machine described therein. This applies in particular to all

statements regarding performance or service life and the agreed liability for faults or defects. The

provisions of the contract regarding the liability for faults or defect are neither extended nor restric-

ted by any statements in this manual.

1 Introduction

1.2 Important Notes about this Manual

10 User Manual SIPLACE TX V1/V2 Series JEDEC Tray Feeder (JTF-ML2) 11/2019

1.2.4 Release History

Document

SIPLACE TX V1/V2 Series

JEDEC Tray Feeder (JTF-ML2)

User Manual

Release Amendments

06/2017 Initial release

12/2018 Adding machine type SIPLACE TX V2 to the scope of the document.

11/2019 Addition/Update of the following subjects:

●

Risk of crashing when using thick JEDEC trays

●

Prerequisites and restrictions

(new head types for SIPLACE TX V2)

●

Scope of delivery SIPLACE TX V1 updated (cable: Power Adapter JTF

[03160347‑xx])

●

Establishing the electrical connections on the SIPLACE TX-Series V2 (up-

dated)

●

Magnets with reduced height for Cookie Trays

●

Magnets with reduced height [03160331‑xx] for use with magazine sheets

(Cookie Trays))

●

Appendix (FCU added)

1.2.5 Further Information and Contents of Documentation Pack

1.2.5.1 How To Get Information

If you have any questions about this manual or if you would like more information about certain

subjects, please contact your local SIPLACE branch or us directly:

ASM Assembly Systems GmbH & Co. KG

Rupert-Mayer-Str. 44

81379 München

1.2.5.2 SIPLACE on the World Wide Web (WWW)

You can choose between the German and English version.

The different sections contain information about our products, services and contact persons.

In addition, registered customers can also access the MySIPLACE user group. Here you can call

up special information about our placement systems, e.g.

●

technical documentation

●

technical information

●

spare parts lists etc.

Registration for the MySIPLACE user group is very simple:

► At the head of the web site, click on

and then on the Register

link.

► Fill in the registration form and send it off to us.

Soon afterwards, you will receive your access authorization with user name and password.