00196478-08_MM_SX12DX12_en.pdf - 第47页
Major Maintenance 5.2.2 Performing Maintenance Ta sks Maintenance Tasks for Base Ma chine Maintenance Manual SIPLACE SX1/SX2/DX1/DX2 47 5.2.2.2 5 . 2 . 2 . 2 C h e c k in g a n d C le a n in g / R e p la c in g t h e C o…
Major Maintenance
Maintenance Tasks for Base Machine 5.2.2 Performing Maintenance Tasks
46 Maintenance Manual SIPLACE SX1/SX2/DX1/DX2
Monitoring the Reject Ducts
Conveyor - Monitoring the Nozzle Magazines
Monitoring the Nozzle Magazines
► Remove the reject duct (1). A message should imme-
diately appear on the control panel.
NOTICE!
Monitoring the component reject duct is optional.
If no message appears, check whether this option is in-
stalled on your system.
If the option is installed on your system and no message
appears, please contact your local SIPLACE Service
team.
► Fit the reject duct back into place.
► Repeat the procedure for all reject ducts.
NOTICE!
Twin magazines are permanently fixed and cannot be re-
moved. For this reason, this check is not applicable for
Twin magazines.
► Remove the nozzle magazines.
► Close the covers and press the Start button.
⇨ Depending on the station software, the station must
display all removed nozzle magazines.
Major Maintenance
5.2.2 Performing Maintenance Tasks Maintenance Tasks for Base Machine
Maintenance Manual SIPLACE SX1/SX2/DX1/DX2 47
5.2.2.2
5.2.2.2 Checking and Cleaning/Replacing the Compressed Air Filter (if required)
Checking and Cleaning/Replacing the Compressed Air Filter (if required)
5.2.2.3
5.2.2.3 Cleaning/Replacing the Head Exhaust Air Filter
Cleaning/Replacing the Head Exhaust Air Filter
CAUTION!
Before checking or replacing the compressed air filters,
you need to shut off the supply of air!
► Open the cover (1) on the pneumatic system.
► Push the lever (2) for the compressed air supply
back, until it is positioned horizontally.
► All manometers must be set to zero.
► Push the yellow lock (3) on the black protective cap
up. Twist off the protective cap.
► Press the glass tube (1) upwards and unscrew it.
► Unscrew the filter (2).
► Pull out the filter for the compressed air maintenance
unit and check for dirt.
► Replace the filter if it is dirty. (filter element 5 µm
[00355386-xx])
► Installation is performed by following the above in-
structions in the reverse order.
► Unscrew the head exhaust air filter. Clean it with a
compressed air device or replace the filter if heavily
soiled. (filter element 40 μm [03003717-xx])
Major Maintenance
Maintenance Tasks for Base Machine 5.2.2 Performing Maintenance Tasks
48 Maintenance Manual SIPLACE SX1/SX2/DX1/DX2
5.2.2.4
5.2.2.4 Cleaning the Protective Covers
Cleaning the Protective Covers
CAUTION
ESD coating
► The choice of cleaning agent for the protective covers must be made with particular care so
as not to damage the ESD coating on the protective covers! Never use acid or strong alka-
line agents and avoid all ketones, esters, aromatics, halogenated hydrocarbons, etheric oils
or similar.
► Only apply light pressure as you clean the protective covers so as not to damage the ESD
coating!
► Check the protective covers for dirt.
► Clean them with a dry, lint-free cloth, if required.
► If they are very dirty, use a lint-free cloth and a small
amount of a neutral or slightly alkaline cleaning
agent.
► After cleaning, wipe over with fresh water.