00196478-08_MM_SX12DX12_en.pdf - 第67页
Major Maintenance 5.6.3 Performing Maintenance Ta sks Maintenance Tasks for the Con veyor Maintenance Manual SIPLACE SX1/SX2/DX1/DX2 67 5.6.3 5 . 6 . 3 P e r f o r m in g M a in t e n a n c e T a s k s Performing Mainten…
Major Maintenance
Maintenance Tasks for the Conveyor 5.6.1 Tools, Consumables, Spare and Wear Parts
66 Maintenance Manual SIPLACE SX1/SX2/DX1/DX2
5.6
5.6 Maintenance Tasks for the Conveyor
Maintenance Tasks for the Conveyor
5.6.1
5.6.1 Tools, Consumables, Spare and Wear Parts
Tools, Consumables, Spare and Wear Parts
▪ ESD wristband [00320279-xx]
▪ OIL Interflon Fin Super (teflon oil) [03017760-xx]
▪ Lint-free cleaning tissues [03082092-xx]
▪ Ethanol
Isopropanol – IPA can be used as an alternative.
▪ SIPLACE cleaning tissue [00315253-xx]
▪ Protective latex gloves [00372972-xx]
▪ Cotton gloves [00359087-xx]
5.6.2
5.6.2 Preparatory Steps
Preparatory Steps
Caution Conveyor - No PCB Must Be in the Conveyor
Note Co nveyor - Re commendation: Ad justing Sides via S oftware for Acces sibility
► Move the component trolley out of the machine.
See also
1.2 Preparatory Work... [ ➙ 12]
CAUTION
No board
There must be no PCBs in the machine during the following tasks.
NOTICE
Accessibility
We recommend using the following procedure for better access:
► Use the station software to adjust the conveyor sides in such a way that you can easily
reach all conveyor belts as well as the whole area below the sides.
Major Maintenance
5.6.3 Performing Maintenance Tasks Maintenance Tasks for the Conveyor
Maintenance Manual SIPLACE SX1/SX2/DX1/DX2 67
5.6.3
5.6.3 Performing Maintenance Tasks
Performing Maintenance Tasks
5.6.3.1
5.6.3.1 Cleaning and Preserving the Conveyor
Cleaning and Preserving the Conveyor
Preservi ng the Conveyor - Preparator y Tasks: Moving Sides Etc.
Moving the Conveyor Sides
► Move all conveyor sides to one side of the conveyor.
DC: Use the station software to set the dual conveyor to single conveyor mode (right).
SC: Use the station software to move the moveable side to one side of the conveyor.
► First perform the following cleaning and preserving steps only to the side of the conveyor which is
now free.
Cleaning and Preserving the Hexagonal Shafts
CAUTION
Observe the exact order
► Observe the following steps in exactly the order shown.
NOTICE
Keeping the clamping surfaces clean (dual conveyor only)
► During work, keep the clamping surface free of any dirt or oil. This makes subsequent
cleaning much easier.
Overview of the hexagonal shafts in the conveyor
► Apply Teflon oil to a lint-free cloth and clean the hex-
agonal shafts (1) in the conveyor.
Alternatively you can also use a SIPLACE cleaning
tissue.
CAUTION!
Never apply the Teflon oil to the cloth inside the machine.
Where possible, go away from the machine.
► Repeat the procedure for all hexagonal shafts in the
conveyor.
Major Maintenance
Maintenance Tasks for the Conveyor 5.6.3 Performing Maintenance Tasks
68 Maintenance Manual SIPLACE SX1/SX2/DX1/DX2
Cleaning and Preserving the Linear Guides
SXDX12 V1 Cleaning and Preserving the Linear Guides
Cleaning and Preserving the Ball Screws
Overview of the linear guides in the conveyor
► Clean the linear guide rails for the conveyor sides (1)
and the width adjustment with a SIPLACE cleaning
tissue.
► Repeat the procedure for all linear guide rails in the
conveyor.
Overview of the ball screws in the conveyor