00196478-08_MM_SX12DX12_en.pdf - 第72页
Major Maintenance Maintenance Tasks Nozzle Magazi nes 5.7.1 Tools, Consumables, Spa re and Wear Parts 72 Maintenance Manual SIPLACE SX1/SX2/DX1/DX2 5.7 5 . 7 M a in t e n a n c e T a s k s N o z z le M a g a z in e s Mai…
Major Maintenance
5.6.4 Final Work Maintenance Tasks for the Conveyor
Maintenance Manual SIPLACE SX1/SX2/DX1/DX2 71
5.6.4
5.6.4 Final Work
Final Work
► Restore the original conveyor configuration.
Major Maintenance
Maintenance Tasks Nozzle Magazines 5.7.1 Tools, Consumables, Spare and Wear Parts
72 Maintenance Manual SIPLACE SX1/SX2/DX1/DX2
5.7
5.7 Maintenance Tasks Nozzle Magazines
Maintenance Tasks Nozzle Magazines
5.7.1
5.7.1 Tools, Consumables, Spare and Wear Parts
Tools, Consumables, Spare and Wear Parts
▪ SIPLACE cleaning tissue [00315253-xx]
5.7.2
5.7.2 Performing Maintenance Tasks
Performing Maintenance Tasks
5.7.2.1
5.7.2.1 Cleaning the Twin Nozzle Magazines
Cleaning the Twin Nozzle Magazines
► Insert the nozzles into the nozzle garages.
► Remove the nozzles from the nozzle garages.
► Clean the nozzles with a SIPLACE cleaning tissue.
CAUTION!
Pay particular attention on the spring retainer.
Major Maintenance
5.8.1 Tools, Consumables, Spare and Wear Parts Maintenance Tasks for Vacuum Pump
Maintenance Manual SIPLACE SX1/SX2/DX1/DX2 73
5.8
5.8 Maintenance Tasks for Vacuum Pump
Maintenance Tasks for Vacuum Pump
SXDX12V2 The vacuum pum p is an opti on
5.8.1
5.8.1 Tools, Consumables, Spare and Wear Parts
Tools, Consumables, Spare and Wear Parts
▪ If needed, filter insert [03077677-xx]
SXDX12V2
▪ Assembly instructions for vacuum pump SX1/SX2 [00196614-xx]
▪ Service manual for your machine
5.8.2
5.8.2 Preparatory Steps
Preparatory Steps
Risk of injury when working near the tap e cutter
► Switch off the machine and secure it to prevent unauthorized reactivation. Observe the instructions
in section "1.2 Preparatory Work..." [ ➙ 12].
► Interrupt the compressed air supply to the machine.
SXDX12V2
► Dismantle the waste slide. Read the service manual for your machine first.
► Dismantle the cover plate over the vacuum pump.
5.8.3
5.8.3 Recommended maintenance intervals
Recommended maintenance intervals
NOTICE
The vacuum pump is an option.
The vacuum pump is located at location 2 behind the COT-insert.
WARNING
Risk of injury when working near the cutter.
When working in the area of the tape cutter, move the component trolley out of the machine
and disconnect the machine from the mains supply and the compressed air supply.
► Wait until the operating pressure has dropped to 0 MPa.
► Always secure the machine against unauthorized reactivation.
► Do not reach into the tape cutter.
CAUTION
Make sure you do not damage any cables and hoses.
CAUTION
Loosened vacuum pump
It is possible to remove the vacuum pump from the machine but it is not necessary.
For a better access, however, it may be useful to loosen the vacuum pump and pull it a bit to
the front within the machine. Also read the Assembly Instructions for the vacuum pump.
► Make sure that the vacuum pump cannot fall out of the machine.
Maintenance inter-
val
Spare part Task
Every 6 months Filter insert [03077677-xx] Check the filter insert and replace if necessary.
NOTICE
Working life
The filter insert has a working life of at minimum 7500 hours up to 25000 hours. For more infor-
mation about the product life, refer to the manufacturer's documentation (see http://www.beck-
er-international.com – Vacuum pump rotary vane pumps, dry running, type VX4.25)