OM-1352-003_w.pdf - 第53页

6-4 Tg1357-ID-SO 0703-003 Component ID Component IDs can be speciﬁed in each text box. When one of the unit No. buttons ([Unit #1] through [Unit #4] buttons) is selected, the corresponding dispensing unit No. is displaye…

6-3

Tg1357-ID-SO

0703-003

[2] [Unit #1] through [Unit #4] Buttons

Select the ﬂux dispensing unit to be used.

When a ﬂux dispensing unit is selected, the ID is displayed in the text

box entitled "Component ID".

[3] List of Placement Feeder Location Data

Set the ﬂux spreading unit to be installed on each feeder base.

Fdr No.

This indicates the feeder Nos. where ﬂux dispensing units can be

arranged.

Note

Up to 5 feeder Nos. (Fdr Nos. equivalent to 5 lanes) can be used for

one feeder base.

x01

x49

2 1

25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

2 12 12 1

Connector on Feeder

Base Side

Connector on Flux Transfer

Device Side

Unit #4

<FLUX.UNIT #4>

Unit #3

<FLUX.UNIT #3>

Unit #2

<FLUX.UNIT #2>

Unit #1

<FLUX.UNIT #1>

Fig. 20 Example of One Feeder Base with Maximum Number of Flux Dispensing Units

2 1

4 3 2 1

x 49

25 24 23 22

2 1

For Blocks 1 and 4 For Blocks 2 and 3

Multi-Layer Tray Feeder

(JEDEC Size)

Multi-Layer Tray Feeder

(JEDEC Size)

Unit #1

x 01

Fig. 21 Multi-Layer Tray Feeder on Each Block

6.1 Pattern Program

6-4

Tg1357-ID-SO

0703-003

Component ID

Component IDs can be speciﬁed in each text box.

When one of the unit No. buttons ([Unit #1] through [Unit #4] buttons)

is selected, the corresponding dispensing unit No. is displayed like

"FLUX. UNIT #1" to "FLUX. UNIT #4".

Set a control command.

Notice

If a control command other than the following ones is used, the

step becomes invalid.

- (hyphen) :

This command handles the steps as those for the

placement feeder location data.

E : This command shows the end of the placement feeder

location data.

The step where "E" is set is valid.

S : This command invalidates the steps speciﬁed as

placement feeder location data.

X : This command invalidates the steps speciﬁed as

placement feeder location data and shows the end of

the data.

Comment

Set a comment for each Fdr No.

Up to 32 characters can be used.

Alphanumeric characters and symbols can be used.

Note

(a) The performance of the machine is not affected by these

commands. In other words, it has nothing to do with or without

these comments.

(b) It is recommended to set helpful information on components

related to the feeder Nos. (Fdr Nos.).

Feeder Fixed

Select "Enable" or "Disable" to determine whether or not the feeder

positions should be ﬁxed in place.

When "Enable" is selected, the feeder Nos. (Fdr Nos.) and the

component IDs are not affected by any insert and delete operations of a

component.

Disable :

The feeder position is not ﬁxed.

Enable : The feeder position is ﬁxed.

6.1 Pattern Program

6-5

Tg1357-ID-SO

0703-003

Feeder Alternate

Select "Enable" or "Disable" to determine whether or not the feeder

alternate function should be used.

Disable :

The feeder alternate function is not used.

Enable :

The feeder alternate function is used.

Fdr No.

When "Enable" is selected for the feeder alternate function, set the

destination feeder No. (Fdr No.) of the feeder that will work in place of

the feeder where a component pickup error has occurred in succession.

Reference

Refer to "1.4 Placement Feeder Location Data" in "Chapter 3" of the

instruction manual (Vol. 3 for the main machine) for details.

Setting Procedure of Placement Feeder Location Data

Procedure

(1) Press the icon ( ) when the "Placement Feeder Location" tab sheet is

active. The "Feeder Base" subtab sheets become valid and can be used

to specify each ﬂux dispensing unit.

(2) Select each unit No. button ([Unit #1] through [Unit #4] buttons) in the

required "Feeder Base #" subtab sheet.

(3) Specify parameters (number of rotations) in the "No. of Rot. [rot.]" text

boxes for the speciﬁed unit No.

6.1 Pattern Program