DeltaTherm_IR_REV_C.pdf - 第23页

DeltaTherm IR Cure Module Revision C / Sept ember 2022 Page 23 of 41 Sensors 216B215B215B The PIP Sensors can be monitor ed in Manual mode for corr ect operation. 217B216B216B 15B15B15B Figure 16 : Sensors in Manual Mod …

DeltaTherm IR Cure Module

Revision C / September 2022

Page 22 of 41

214B213B213BThe Conveyor Width can be set in Manual mode.

1. 80B79B79BPress to manually enter the target conveyor width setpoint.

• 81B80B80BTouch the screen and a keypad will be shown.

• 82B81B81BEnter the necessary value.

• 83B82B82BPush ‘ENT’, and the zone screen will be shown again.

2. 84B83B83BPress to move the current target conveyor width setpoint.

276B275B275BNote: Prior to the move, the machine will check for any boards.

3. 85B84B84BPress to rehome the conveyor width.

277B276B276BNote: Prior to the move, the machine will check for any boards.

Conveyor Jog

215B214B214B

14B14B14BFigure 15: Conveyor Jog in Manual Mode

1. 86B85B85BThis screen displays the current conveyor width.

2. 87B86B86BPress to adjust the conveyor width. This will jog the conveyor width in a positive or

negative direction.

278B277B277BNote: The clearboard sequence will not run prior to the jog.

DeltaTherm IR Cure Module

Revision C / September 2022

Page 23 of 41

Sensors

216B215B215BThe PIP Sensors can be monitored in Manual mode for correct operation.

217B216B216B

15B15B15BFigure 16: Sensors in Manual Mode

279B278B278BNote: Process PIP will only show on 12 ft and 16 ft oven length systems.

SMEMA Control

1. 88B87B87BThe SMEMA inputs (Upstream Board Available and Downstream Ready) can be

monitored for correct operation through the SMEMA screen in Manual mode.

2. 89B88B88BSelect the necessary output (Machine Ready and Board Available) to toggle it on or

off.

218B217B217B

16B16B16BFigure 17: SMEMA in Manual Mode

DeltaTherm IR Cure Module

Revision C / September 2022

Page 24 of 41

Setup Mode

219B218B218BIn Setup mode, the operator can set basic functions of the machine and Auto Cycle

parameters. These parameters (depending on the machine) are the current recipe, IR panel

temperatures, allowable deviations, conveyor width, and conveyor speed. Parameters are

saved in the controller under the current recipe even when the module is shut down. Push

the Home button or the F3 button at any time to exit Setup mode and return to cycle stop.

IR Panels

220B219B219B

17B17B17BFigure 18: Setup Zone 1 Panels

1. 90B89B89BThe Heater Panel Recipe Switch can disable or enable the use of a zone’s upper or

lower heater panel in Autocycle. If enabled, the panel will display a green

checkmark . If disabled, the panel will display a red X .

280B279B279BNote: IR panels cannot activate unless the exhaust fan is on.

2. 91B90B90BThe Setpoint box is the target temperature (display temperature is filtered) for

each zone and the deviation box is the permitted deviation from the setpoint for

that zone.

• 92B91B91BTouch the Setpoint box and a keypad will be shown.

• 93B92B92BEnter the necessary value. The system minimum and maximum are shown

below the numeric field.

• 94B93B93BPress “ENT” to save the value and close the keypad.