DeltaTherm_IR_REV_C.pdf - 第32页
DeltaTherm IR Cure Module Revision C / Sept ember 2022 Page 32 of 41 Error Messa ges 232B231B231B The following are all the possible error messages g enerated by th e PLC program. Msg Number DeltaTherm Fault Mess ages 10…
DeltaTherm IR Cure Module
Revision C / September 2022
Page 31 of 41
Recovery from an Over-Temperature Error
1. 137B136B136BSelect “Silence Horn” to stop the alarm or “Clear Fault” to clear the fault.
2. 138B137B137BLet the module temperature decrease.
3. 139B138B138BOperate the module in manual mode or restart Auto Cycle. Look for the parameter
that causes the error.
4. 140B139B139BIf the error continues to repeat, refer to Section 12.
Recovery from an Auto Conveyor Adjust Error
229B228B228BIn the conveyor homing procedure, two errors may occur:
230B229B229BError 1: The conveyor passes the home position sensor and hits the hard stop on one side.
1. 141B140B140BWhen the conveyors pass the sensor and hit the hard stop, engage the “Emergency
Stop” button.
2. 142B141B141BOpen the left cabinet and find fuse number 70.
3. 143B142B142BRelease the fuse and disengage the “Emergency Stop” button. This will move the
conveyor toward the sensor.
4. 144B143B143BWhen the conveyor passes the sensor, engage the “Emergency Stop” button again.
5. 145B144B144BExamine the integrity and the wiring of the sensor.
6. 146B145B145BInstall fuse number 70, and home the conveyor again.
231B230B230BError 2: The conveyor passes the software limit and hits the hard stop on the other side.
1. 147B146B146BEngage the “Emergency Stop” button.
2. 148B147B147BOpen the left cabinet and find the conveyor direction relay (CR11).
3. 149B148B148BPull the blue button and disengage the “Emergency Stop” button. The conveyor
will move away from the hard stop.
4. 150B149B149BEngage the “Emergency Stop” button again. This will stop the conveyor.
5. 151B150B150BPush the blue button so it is in the original position in the relay.
6. 152B151B151BExamine the wire and the conveyor position encoder.
DeltaTherm IR Cure Module
Revision C / September 2022
Page 32 of 41
Error Messages
232B231B231BThe following are all the possible error messages generated by the PLC program.
Msg Number
DeltaTherm Fault Messages
100
Zone 1/2 Overtemp Monitor Fault
101
Zone 3/4 Overtemp Monitor Fault
102
Zone 5/6 Overtemp Monitor Fault
103
Zone 7/8 Overtemp Monitor Fault
104
Exhaust Fan Low Pressure.
105
Panel 1A Overtemp >285C
106
Panel 1B Overtemp >285C
107
Panel 2A Overtemp >285C
108
Panel 2B Overtemp >285C
109
Panel 3A Overtemp >285C
110
Panel 3B Overtemp >285C
111
Panel 4A Overtemp >285C
112
Panel 4B Overtemp >285C
113
Master Conveyor Width (CAN4) Drive Homing Timeout
114
Slave Conveyor Width (CAN6) Drive Homing Timeout
115
Data Table Error Values Not Downloaded
118
System Options Changed Reboot Required.
131
Control Power Timeout Fault
132
Autocycle Idle Timeout
141
Master Conveyor Transfer (CAN3) Communication Timeout
142
Master Conveyor Width (CAN4) Communication Timeout
143
Slave Conveyor Transfer (CAN5) Communication Timeout
145
Slave Conveyor Width (CAN6) Communication Timeout
147
Board Process Timeout Error
148
Panel 5A Overtemp >285C
149
Panel 5B Overtemp >285C
150
Panel 6A Overtemp >285C
DeltaTherm IR Cure Module
Revision C / September 2022
Page 33 of 41
151
Panel 6B Overtemp >285C
152
Panel 7A Overtemp >285C
153
Panel 7B Overtemp >285C
154
Panel 8A Overtemp >285C
155
Panel 8B Overtemp >285C
156
Zone 1A Intensity Fault Panel Never Reached Setpoint
157
Zone 1B Intensity Fault Panel Never Reached Setpoint
158
Zone 2A Intensity Fault Panel Never Reached Setpoint
159
Zone 2B Intensity Fault Panel Never Reached Setpoint
160
Zone 3A Intensity Fault Panel Never Reached Setpoint
161
Zone 3B Intensity Fault Panel Never Reached Setpoint
162
Zone 4A Intensity Fault Panel Never Reached Setpoint
163
Zone 4B Intensity Fault Panel Never Reached Setpoint
164
Zone 5A Intensity Fault Panel Never Reached Setpoint
165
Zone 5B Intensity Fault Panel Never Reached Setpoint
166
Zone 6A Intensity Fault Panel Never Reached Setpoint
167
Zone 6B Intensity Fault Panel Never Reached Setpoint
168
Zone 7A Intensity Fault Panel Never Reached Setpoint
169
Zone 7B Intensity Fault Panel Never Reached Setpoint
170
Zone 8A Intensity Fault Panel Never Reached Setpoint
171
Zone 8B Intensity Fault Panel Never Reached Setpoint
173
Zone 1A Deviation Fault
174
Zone 1B Deviation Fault
175
Zone 2A Deviation Fault
176
Zone 2B Deviation Fault
177
Zone 3A Deviation Fault
178
Zone 3B Deviation Fault
179
Zone 4A Deviation Fault
180
Zone 4B Deviation Fault
181
Zone 5A Deviation Fault
182
Zone 5B Deviation Fault