TSR2000-Series-Hardware-User-Guide-V1.pdf - 第26页

26 6. TRO UBLE SHO OTING 1. The System cannot R eset af ter Booting. Emergency swit ch erro r ⚫ Check the Emer gency switch is not pressed, by mistak e. 2. Z axis or X and Y axis c annot be Positioned Accurately in Pr oc…

5.3 Syringe Mounting Bracket – Attachment

From the main screen, on the teaching pendant,

press 4. Use the jog keys to move the head into

a central position and lower head until there is

sufficient access to the rear of the bracket. Use

SHF button to change movement speed. Follow

instructions below.

1. Move and lower head using teaching

pendant.

2. Remove mounting plate.

4. Attach attach top bracket.

3. Secondary plate should be exposed

5. Attach bottom bracket from behind.

6. Install syringe and lightly tighten thumb

screws.

6. TROUBLE SHOOTING

1. The System cannot Reset after Booting.

Emergency switch error

⚫ Check the Emergency switch is not pressed, by mistake.

2. Z axis or X and Y axis cannot be Positioned Accurately in Processing

1) Loss of steps will cause inaccurate positioning phenomenon.

Overload, excessive speed or acceleration, insufficient power supply, or mismatched motor drive would lead to

the loss of steps. Please check the overload and the parameters settings. If the inaccurate positioning

phenomenon disappears or remits after reducing the speed or acceleration, we can make sure the phenomenon

is caused by the motor loss of steps. If inaccurate positioning phenomenon is very obvious for one axis, reduce

the acceleration of the axis.

2) Operation Error will cause inaccurate positioning phenomenon.

Do not reset when the work done

Make the system reset automatically after each accumulated processing error has been eliminated,)

7. WARRANTY

Manufacturer warrants this product to the original purchaser for a period of one (1) year from date of purchase to

be free from defects in material and workmanship, but not against damages by misuse, negligence, accident, faulty

installations and instructions. Manufacturer will repair or replace (at factory’s option), free of charge, any

component of the equipment thus found to be defective, on return of the component, “PREPAID” to the factory

during the warranty period. In no event shall any liability or obligation of the Manufacturer arising from this

warranty exceed the purchase price of the equipment. This warranty is only valid if the defective product is returned

as a complete assembly without physical damage. The Manufacturer’s liability, as stated herein, cannot be altered

or enlarged except by a written statement signed by an officer of the company. In no event shall the Manufacturer

be liable for consequential or incidental damages. A return authorization is required from Techcon Systems prior

to shipping a defective unit to the factory.

Manufacturer reserves the right to make engineering product modifications without notice.

All returns must be issued with a Returns Authorization number, prior to return. Send warranty returns to:

Techcon Systems Corporate Headquarters,

10800 Valley View Street, Cypress, 90630, USA.

Tel: 1-714-230-2398, Fax: 1-714-828-2001

E-mail: oemorders@okinternational.com

Techcon Systems European Corporate Office,

Eagle Close, Chandler’s Ford Industrial Estate,

Eastleigh, Hampshire, SO53 4NF, UK.

Tel: +44 2380 489 100, Fax: +44 2380 489 109

E-mail: europe-orders@okinternational.com

Or visit www.techcon.com

Manufacturer: Dover (Shenzhen) Industrial Equipment Manufacturing Co., Ltd

Floor West, 1 Building, Tingwei Industrial Park,

6 Liufang Road, Boa’an District,

Shenzhen, China

Manufacturer Contact: OK International Ltd.

Ian Jennings

Chandlers Ford, Hampshire Tel: +44 (0) 23 8048 9000

England SO53 4NF Fax: +44 (0) 23 8048 9109

Declares that the product(s): Industrial Robot/Bench-top Robot

Model Numbers: TSR2201, TSR2301, TSR2401

Option Kit Model Numbers:

TSR2200-SC

TSR2300-SC

TSR2400-SC

Is intended to be incorporated into machinery or to be assembled with other machinery to

constitute machinery covered by Directive 2006/42/EC.

And that the following harmonized standards and specifications have been used:

EN ISO 10218-1:2011

EN ISO 12100:2010

EN 60204-1/A1:2009

And furthermore declares that the product(s) covered by this Declaration must not be put into

service until the machinery into which it is to be incorporated or of which it is a component

has been found and declared to be in conformity with the provisions of directive 2006/42/EC.

Signature: Date: May 23

, 2014

Jimmy Guo

Quality Engineer

Manufacturer’s Declaration of Incorporation

Directive: Machinery Directive 2006/42/EC