00195376-05_SM_D1_D1i_D2_D2i_EN.pdf - 第140页

Service Work C&P6/12 Head 4.4.13 Replacing the "Z Axis Down" Sensor [00321524 -xx] 140 Service Manual SIPLACE D1/D1i/D2/D2i 4.4.13 4 . 4 . 1 3 R e p la c in g t h e " Z A x is D o w n " S e n s o …

Service Work

4.4.12 Replacing the Z Axis Toothed Belt [00334936-xx] C&P6/12 Head

Service Manual SIPLACE D1/D1i/D2/D2i 139

See also

 6.5.6 Setting the Z axis Belt Tension [ ➙ 235]

NOTICE!

Make sure that both ends (2) of the tension jack lie on the

teeth of the toothed belt (1) .

NOTICE!

New tension jack

A new tension jack (fitted from 10/2007) has a profile

which engages with the toothed belt and therefore en-

sures a more reliable clamping.

► Loosely screw in the four M3x5 hexagon socket-head

screws (1) on the Z axis drive unit (2).

► Tension the Z axis toothed belt (7) by pushing the Z

axis drive unit upwards.

► Check the toothed belt tension with the belt tension

measuring device.

► Tighten the two M3x14 hexagon socket-head screws

(6) to fix the motor clamp (5).

► Fix the motor clamp 2 (4) with the two M2.5x12 hex-

agon socket-head screws (3).

► Now tighten the hexagon socket-head screws on the

Z axis drive unit and the motor clamp.

► Check the Z axis top stop with the setting gauge.

Frequency in Hz Before continuous opera-

tion run

After continuous operation

run

Toothed belt T2 / DLM3 on the Z axis 280 +/- 10 280 +/- 10

Service Work

C&P6/12 Head 4.4.13 Replacing the "Z Axis Down" Sensor [00321524-xx]

140 Service Manual SIPLACE D1/D1i/D2/D2i

4.4.13

4.4.13 Replacing the "Z Axis Down" Sensor [00321524-xx]

Replacing the "Z Axis Down" Sensor [00321524-xx]

Removal

Installation

Adjusting the "Z axis down" sensor

► Set the distance between the white sleeve ring and the light barrier to 0.95 -1.15 mm.

⇨ Use a test probe or drill (diameter 1.0 mm) for this.

⇨ Check the distance with a test probe or drill (diameter 1.2 mm). – This drill should not fit!

1. "Z axis down" sensor

2. Fixtures for sensor

3. Plug for intermediate distributor

► Dismantle the front part of the C&P head.

► Dismantle the star.

► Remove the plug from the slot on the intermediate

distributor.

► Push the Z axis down.

► Loosen the screws holding the sensor (2).

► Remove the cable clamps on the driver arm and star

motor.

► Carefully pull the sensor and cable out of the front

part of the C&P head and remove the plug (3) from

the socket on the intermediate distributor.

► Thread the sensor cable from the Z axis into the front

part of the C&P head.

► Fix the sensor (1) in position with the screw provided

(2) and initially screw loosely into the jaw of the Z ax-

is.

► Fix the cable into place with the cable clamps.

► Check how the cable is run inside the front part of the

C&P head:

⇨ If the Z axis has been pushed right out, the cable

should lie loosely around the housing for the star

drive shaft. The cable must NOT be pulled tight.

⇨ If the Z axis is pushed right in, the cable should run

freely inside the front part of the C&P head, with-

out touching the rotary encoder for the DP axis.

CAUTION!

Check how the cables are run!

If the radius of the curvature is too small, the Z axis could

jam or the light barrier cable could break.

► Once the cable is run in line with the required condi-

tions, fix it in place with the angled clips.

► Connect the cable plug to the slot on the intermediate

distributor.

Service Work

4.4.14 Replacing the Complete Z Axis [03001959-xx] C&P6/12 Head

Service Manual SIPLACE D1/D1i/D2/D2i 141

► Fix the light barrier in place with the two screws provided.

► Fit and adjust the star.

► Fit the front part of the C&P head.

► Check the sensor function.