00193796-08.pdf - 第35页
Installation Manual, Station Software Version 505.04 Edition 07/2006 35 of 156 4.3.1.6 Base, Extended, Total Memory The type and size of the recognized DRAM memory is indicated here. Base Memory Memory below 1 Mbyte with…
Installation Manual Station Software Version 505.04
34 of 156
4.3.1.3 Drive A / Drive B
Drive A: Set the format of floppy drive A: None, 360K, 5.25 in.; 1.2M, 5.25 in.;
720K, 3.5 in.; 1.44M, 3.5 in.;
2.88M, 3.5 in.
Drive B: Set the format of floppy drive B:
None, 360K, 5.25 in.; 1.2M, 5.25 in.;
720K, 3.5 in.; 1.44M, 3.5 in.;
2.88M, 3.5 in.
For drive A: None is set for fail-safe and 1.44M, 3.5in. for optimized default.
For drive B: None applies in both cases
4.3.1.4 Video
Enter the type of graphics adapter in this field. Options are: EGA/VGA, CGA 40, CGA 80, Mono (for
Hercules and MDA). If an adapter has been installed with VGA or a higher resolution, select
EGA/VGA. The default setting is EGA/VGA.
4.3.1.5 Halt On
If this option is activated, the BIOS stops if it detects an error during the boot phase and issues an
error message. If this option is not activated, the BIOS continues without an error message and
uses the default values for processing. If the option is activated, the following causes of errors can
additionally be ruled out:
All Errors
Every error generates an error message.
No Errors No error generates an error message.
All, But
Keyboard
Keyboard errors do not generate an error message.
All, But Diskette Diskette and hard disk errors do not generate an error message.
All, But Disk/Key Diskette, hard disk and keyboard errors do not generate an error message.
All, But Keyboard is selected as the default setting.
Installation Manual, Station Software Version 505.04 Edition 07/2006
35 of 156
4.3.1.6 Base, Extended, Total Memory
The type and size of the recognized DRAM memory is indicated here.
Base Memory
Memory below 1 Mbyte without the adapter hole (usually 640 kbyte)
Extended Memory Available memory above 1 Mbyte
Total Memory
1
Total memory, sum of all areas
4.3.1.7 Setup page "BIOS Features Setup"
This option comprises configuration entries which enable enhanced performance or customized
setting of the system.
In the "Selection options" column, the setting for fail-safe default is indicated in italics and the setting
for optimized default is underlined
.
1
Note that less memory is indicated here than is installed, as the onboard graphics controller reserves 1Mbyte of
the main memory for itself
Installation Manual Station Software Version 505.04
36 of 156
Menu item Note Selection
options
Virus Warning
If the option is enabled, you will receive a warning if a
program wishes to write to the boot sector or the partition
table of the hard disk.
Enabled
Disabled
CPU Internal Cache
1)
This option allows the internal cache to be enabled or
disabled.
Enabled
Disabled
External Cache
1)
You can enable the external cache here. Enabled
Disabled
CPU L2 Cache ECC
Checking
The ECC checking function of the level 2 cache of the CPU
can be set here.
Enabled
Disabled
Quick Power On Self
Test
This field enables the self-test to be speeded up when you
power on the computer (POST), by dispensing with a
second, third and fourth test of the SDRAM. For each test,
the system is tested once completely.
Enabled
Disabled
First Boot Device
First device from which to boot Floppy; LS120;
HDD-0; SCSI;
CDROM; HDD-1;
HDD-2; HDD-3;
ZIP100; USB-
FDD; USB-ZIP;
USB-CDROM;
USB-HDD; LAN;
Disabled
Second Boot Device
Second device from which to boot Floppy; LS120;
HDD-0
; SCSI;
CDROM; HDD-1;
HDD-2; HDD-3;
ZIP100; USB-
FDD; USB-ZIP;
USB-CDROM;
USB-HDD; LAN;
Disabled
Third Boot Device
Third device from which to boot Floppy; LS120;
HDD-0; SCSI;
CDROM; HDD-1;
HDD-2; HDD-3;
ZIP100; USB-
FDD; USB-ZIP;
USB-CDROM;
USB-HDD; LAN;
Disabled
Other Boot Device
If none of the set boot devices were found, a search is
made for all possible devices which can be set as a boot
device in one of the three options above, if this entry is set
to Enabled.
Enabled
Disabled
1)
Enabled caches enhance system performance