00193796-08.pdf - 第46页

Installation Manual Station Software Version 505.04 46 of 156 4.3.1.12 Setup page "PNP /PCI Configuration" Menu item Note Selection options PNP OS Installed Yes , if the operating system used is plug and play- …

100%1 / 156
Installation Manual, Station Software Version 505.04 Edition 07/2006
45 of 156
Menu item Note Selection options
HDD Power Down
The time is set here after which the hard disk is switched
to Power Down mode
Disabled;
1 Min; 2 Min;
3 Min; 4 Min;
5 Min; 6 Min;
7 Min; 8 Min;
9 Min; 10 Min;
11 Min; 12 Min;
13 Min; 14 Min;
15 Min
USB KB Wake-Up
From S3
If disabled is set, the system cannot by woken up from the
S3 state (Suspend to RAM) by a USB keyboard.
Enabled
Disabled
CPU Thermal-
Throttling
If the system begins to throttle due to a thermal overload,
this is the ratio in percent: switch-off time / (switch-off time
+ on time). This value is factory set and cannot be
changed.
87,5%
Resume by Alarm
If this option is switched on, the computer is retrieved from
power saving mode at the specified date and time. If 0 is
specified as a date, this is done on a daily basis.
Enabled
Disabled
Date (of Month)
Alarm
all values between 0
and 31
0
Time (hh:mm:ss)
Alarm
valid time
0:0:0
Reload Global Timer
Events
Every event of a device listed below resets the global
counter for suspend mode, if this is enabled.
Enabled
Disabled
Installation Manual Station Software Version 505.04
46 of 156
4.3.1.12 Setup page "PNP/PCI Configuration"
Menu item Note Selection options
PNP OS Installed
Yes, if the operating system used is plug and play-
compatible (e.g. Win9x); No, if it is not
No
Yes
Reset Configuration
Data
Enabled instructs the PNP BIOS to reset all devices and
assignments.
Enabled
Disabled
Resources
Controlled By
The Manual setting can be used to reserve the interrupts
and DMA, otherwise they will automatically be assigned by
the BIOS (PnP Extention).
If no PNP operating system has been installed, use Auto.
Auto (ESCD)
Manual
IRQ Resources
This field is only enabled if the option Manual is enabled
under Resources Controlled By. Pressing the Enter key
will display a submenu in which the interrupts can be
released for assignment by the PNP BIOS (setting PCI/ISA
PnP) or not assigned by the PNP BIOS (setting Legacy
ISA)
PCI/ISA PnP
Legacy ISA
DMA Resources
This field is only enabled if the option Manual is enabled
under Resources Controlled By. Pressing the Enter key
will display a submenu in which the DMA channels to be
assigned by the PNP BIOS are disabled (setting PCI/ISA
PnP) or not assigned by the PNP BIOS (setting Legacy
ISA)
PCI/ISA PnP
Legacy ISA
PCI/VGA Palette
Snoop
Color reproduction may be corrupted with some graphics
adapters such as graphics accelerators or MPEG adapters
which do not conform to the VGA standard. In this case,
set Enabled
Enabled
Disabled
Assign IRQ for USB
Enabled assigns a PCI IRQ to the USB controller. Enabled
Disabled
PCI INT A
PCI INT B
PCI INT C
PCI INT D
Assignment
With this setting, the BIOS can be instructed to assign a
defined IRQ to a PCI interrupt. A prerequisite for this is that
this IRQ is not set to Legacy ISA. When Auto is set, the
BIOS automatically assigns the IRQ.
Auto; 3; 4; 5; 7; 9; 10;
11; 12; 14; 15
Installation Manual, Station Software Version 505.04 Edition 07/2006
47 of 156
4.3.1.13 Setup page "PC Health Status"
In the "Selection options" column, the setting for fail-safe default is indicated in italics and the setting
for optimized default is underlined
.
Menu item Note Selection options
Throttling
Temperature
This setting specifies the internal chip temperature at
which the processor automatically begins thermal
throttling.
90°C/194°F;
100°C/212°F
110°C/110.00°C
All other menu items indicate internal voltages and cannot be changed.
4.3.1.14 Setup page “Frequency/Voltage Control”
In the "Selection options" column, the setting for fail-safe default is indicated in italics and the setting
for optimized default is underlined
.
Menu item Note Selection options
Auto Detect
DIMM/PCI Clk
If this function is Enabled, only CPCI and DIMM slots
which are also occupied are clocked.
Enabled
Disabled
Spread Spectrum
If this function is Enabled, the average frequency of the
clock cycles generated in the clock synthesizer is
modulated within tight boundaries. This widens the noise
spectrum but lowers the amplitude.
Enabled
Disabled