00193796-08.pdf - 第40页

Installation Manual Station Software Version 505.04 40 of 156 Menu item Note Selection options IDE Secondary Master PIO Sets the PIO mode for the master on the secondary IDE channel. Higher values mean faster access. Aut…

100%1 / 156
Installation Manual, Station Software Version 505.04 Edition 07/2006
39 of 156
Menu item Note Selection options
SDRAM RAS-to-CAS
Delay
The delay between the SDRAM enable command and the
SDRAM read/write command can be changed in this field.
2
3
Auto
SDRAM RAS
Precharge Time
The time after a precharge command for a bank until the
bank can be accessed.
2
3
Auto
System BIOS
Cacheable
This function enables the system to cache the BIOS area
as well.
Enabled
Disabled
Video BIOS
Cacheable
This function enables the system to cache the VGA-BIOS
area as well.
Enabled
Disabled
Memory Hole At
15M-16M
If this function is enabled, the memory hole from 15 MB
through 16 MB is reserved for ISA expansion boards which
require this setting. Depending on the operating system
used, the memory ceases to be available to the system as
of 15 MB. Expansion boards can only address memories
of up to 16 MB.
Enabled
Disabled
CPU Latency Timer
Enabled
Disabled
Delayed Transaction
When set to Enabled, this option enables the 32-bit write
buffer for PCI access.
Enabled
Disabled
System Memory
Frequency
The memory frequency can be specified here, if a
processor supporting both 100MHz and 133MHz memory
frequency has been fitted. If a processor which only
supports 100MHz memory frequency has been fitted (e.g.
Celeron 566MHz), this menu item will not be visible.
100MHz
133MHz
Auto
4.3.1.9 Setup page "Integrated Peripherals Feature"
In the "Selection options" column, the setting for fail-safe default is indicated in italics and the setting
for optimized default is underlined
.
Menu item Note Selection options
On-Chip Primary
PCI IDE
Enabling this field enables the primary IDE channel on
which devices can be run.
Enabled
Disabled
On-Chip Secondary
PCI IDE
Enabling this field enables the secondary IDE channel on
which devices can be run.
Enabled
Disabled
IDE Primary Master
PIO
Sets the PIO mode for the master on the primary IDE
channel. Higher values mean faster access. Auto sets the
maximum permissible value for the disk.
Auto; Mode 1;
Mode 2; Mode 3;
Mode 4
IDE Primary Slave
PIO
Sets the PIO mode for the slave on the primary IDE
channel. Higher values mean faster access. Auto sets the
maximum permissible value for the disk.
Auto; Mode 1;
Mode 2; Mode 3;
Mode 4
Installation Manual Station Software Version 505.04
40 of 156
Menu item Note Selection options
IDE Secondary
Master PIO
Sets the PIO mode for the master on the secondary IDE
channel. Higher values mean faster access. Auto sets the
maximum permissible value for the disk.
Auto; Mode 1;
Mode 2; Mode 3;
Mode 4
IDE Secondary
Slave PIO
Sets the PIO mode for the slave on the secondary IDE
channel. Higher values mean faster access. Auto sets the
maximum permissible value for the disk.
Auto; Mode 1;
Mode 2; Mode 3;
Mode 4
IDE Primary Master
UDMA
If Auto is set, UDMA mode is enabled for the master on the
primary IDE channel if it is supported by the disk.
Auto;
Disabled
IDE Primary Slave
UDMA
If Auto is set, UDMA mode is enabled for the slave on the
primary IDE channel if it is supported by the disk.
Auto;
Disabled
UDMA66/100 with 40
Wire
In the specification for UDMA66 and UDMA100, an 80-wire
cable is prescribed. You can use this option to run drives
which support these modes with a short 40-port cable on
the primary IDE channel. If the drive is connected with an
80-port cable, this entry is ignored and UDMA66 and
UDMA100 are set if the drive supports these modes.
Disabled;
Enabled
IDE Secondary
Master UDMA
If Auto is set, UDMA mode is enabled for the master on the
secondary IDE channel if it is supported by the disk.
Auto;
Disabled
IDE Secondary
Slave UDMA
If Auto is set, UDMA mode is enabled for the slave on the
secondary IDE channel if it is supported by the disk.
Auto;
Disabled
UDMA66/100 with 40
Wire
In the specification for UDMA66 and UDMA100, an 80-wire
cable is prescribed. You can use this option to run drives
which support these modes with a short 40-port cable on
the secondary IDE channel. If the drive is connected with
an 80-port cable, this entry is ignored and UDMA66 and
UDMA100 are set if the drive supports these modes.
Disabled;
Enabled
IDE HDD Block
Mode
This enables the transfer of entire blocks from the hard
disk to the memory instead of individual sectors.
Enabled
Disabled
USB Controller
If this setting is disabled, the USB controller is disabled
and no USB devices can be run on the module.
Enabled
Disabled
USB Keyboard
Support
When this option is switched on, a keyboard is supported
on the USB port even after the boot process.
Enabled
Disabled
USB Mouse Support
When this option is switched on, a mouse is supported on
the USB port even after the boot process.
Enabled
Disabled
Init Display First
This option can be used to specify which graphics adapter
is to be used to output video if a PCI graphics adapter is
integrated in the system in addition to the onboard
graphics adapter. If a graphics adapter is connected to the
SMP16 bus, this is always used to output video
irrespective of the setting.
Onboard
PCI Slot
AC 97 Audio
If an AC 97 audio controller is connected to the RPIO, it
can be switched on here
Enabled
Disabled
Installation Manual, Station Software Version 505.04 Edition 07/2006
41 of 156
Menu item Note Selection options
AC 97 Modem
If an AC 97 modem controller is connected to the RPIO, it
can be switched on here
Enabled
Disabled
Onboard LAN
Disabled disables the onboard LAN controller. Enabled
Disabled
Onboard LAN Boot
ROM
In order to boot from the onboard LAN controller, this item
must be enabled.
Enabled
Disabled
Onboard FDC
Controller
Enables the onboard floppy controller
Enabled
Disabled
Onboard Serial
Port 1
Sets the I/O addresses and IRQs of serial port 1 (COM A) 3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
Onboard Serial
Port 2
Sets the I/O addresses and IRQs of serial port 2 (COM B): 3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
Onboard Parallel
Port
Sets the I/O addresses and IRQs of the parallel port: 378/IRQ7
3BC/IRQ7
Disabled
Parallel Port Mode
Sets the mode of the parallel port. This option can be set
when disabled is not set for Onboard Parallel Port
Standard
SPP
EPP1.7
EPP1.9
ECP
ECP+EPP
ECP Mode Use DMA
This option can only be set if ECP or ECP+EPP is selected
for Parallel Port Mode.
1
3