00193796-08.pdf - 第44页

Installation Manual Station Software Version 505.04 44 of 156 4.3.1.11 Setup page "Power Management Setup" Menu item Note Selection options ACPI Support ACPI version 1.0 is implemented in the BIOS. Statuses S1 …

100%1 / 156
Installation Manual, Station Software Version 505.04 Edition 07/2006
43 of 156
Menu item Note Selection options
On board SRAM size
This sets the size of an address window on the onboard
SRAM. The following settings are possible:
Other settings can be made by the user's application.
Disabled
8kByte
16kByte
32kByte
On board SRAM
base adr.
This value is used to specify the base address of the
SRAM window. This value can only be set if the SRAM is
not disabled. The choice of base address depends on the
window size which has been set.
CC000H
1)
CE000H
2)
D0000H
3)
D2000H
2)
D4000H
1)
D6000H
2)
D8000H
3)
DA000H
2)
DC000H
1)
DE000H
2)
Fanless Operation
When this option is enabled, the module can be operated
without fans. The processor then only operates for 50 % of
the time.
Enabled
Disabled
1) For SRAM size 8/16kByte
2) For SRAM size 8kByte
3) For SRAM size 8/16/32kByte
Installation Manual Station Software Version 505.04
44 of 156
4.3.1.11 Setup page "Power Management Setup"
Menu item Note Selection options
ACPI Support
ACPI version 1.0 is implemented in the BIOS. Statuses S1
and S3 are supported by the hardware of the
CPCI-
/SMP16-CPU076.
Enabled, ACPI is only supported automatically as of
Win98. When installing Win95, ACPI installation must be
initiated by hand.
Disabled means that ACPI is also not supported for an
ACPI-compatible operating system.
Enabled
Disabled
ACPI Suspend Type
Specifies the status in which the computer shuts down in
Suspend Mode using ACPI.
S1 (POS)
S3 (STR)
Power Management
This field is the main switch for the power saving modes.
There are three settings:
Max Saving Switches the computer after a brief time of
inactivity to power saving mode.
Min Saving Functions in nearly exactly the same way
as Max Saving, except that the time of
inactivity required before switching is
longer.
User Defined Enables the power saving mode options to
be set individually.
User Define
Min Saving
Max Saving
Video Off Method
This sets the way in which the monitor is switched to
power saving mode. There are three options available:
DPMS (Display Power Management) enables the
BIOS to control DPMS-compatible
graphics adapters.
Blank Screen Darkens the screen and
should be used with monitors without
Power Management functions.
V/H Sync+Blank Darkens the screen by switching off the
vertical and horizontal
scanning.
Blank Screen
V/H Sync+Blank
DPMS
Video Off In
Suspend
Specifies whether the monitor interface is switched off in
suspend mode (no sync signals)
No
Yes
MODEM Use IRQ
This option determines which IRQ registers the ring tone of
the modem for faxing.
NA; 3; 4; 5; 7;9; 10; 11
Suspend Mode
The time is set here before the system switches to
suspend mode.
Disabled;
1 Min; 2 Min;
4 Min; 8 Min;
12 Min; 20 Min;
30 Min; 40 Min;
1 Hour
Installation Manual, Station Software Version 505.04 Edition 07/2006
45 of 156
Menu item Note Selection options
HDD Power Down
The time is set here after which the hard disk is switched
to Power Down mode
Disabled;
1 Min; 2 Min;
3 Min; 4 Min;
5 Min; 6 Min;
7 Min; 8 Min;
9 Min; 10 Min;
11 Min; 12 Min;
13 Min; 14 Min;
15 Min
USB KB Wake-Up
From S3
If disabled is set, the system cannot by woken up from the
S3 state (Suspend to RAM) by a USB keyboard.
Enabled
Disabled
CPU Thermal-
Throttling
If the system begins to throttle due to a thermal overload,
this is the ratio in percent: switch-off time / (switch-off time
+ on time). This value is factory set and cannot be
changed.
87,5%
Resume by Alarm
If this option is switched on, the computer is retrieved from
power saving mode at the specified date and time. If 0 is
specified as a date, this is done on a daily basis.
Enabled
Disabled
Date (of Month)
Alarm
all values between 0
and 31
0
Time (hh:mm:ss)
Alarm
valid time
0:0:0
Reload Global Timer
Events
Every event of a device listed below resets the global
counter for suspend mode, if this is enabled.
Enabled
Disabled