00194932-20 User Manual CAN Test Box-Error Frame Diagnostic unit_en.pdf - 第8页
1 - 8 SIPLACE CAN Bus Edition 10/2018 8 1.1 History of the document Ve r s i o n Edition Modification 00194932-01 1 1/2005 Introduction CAN T est Box 00194932-02 01/2006 Error correction an d improve layout 00194932-03 0…
1 - 7
Edition 10/2018 SIPLACE CAN Bus
7
1 Safety instructions
WARNING:
Comply with the higher ranking "Safety Instructions" in Chapter "Operational Safety" in the User
Manual and Service Manual.
The placement machines SIPLACE are powered by mains voltage.
Portions of the system are therefore conducting dangerous electricity, inside the machine even
while the master switch is turned off.
Death, serious injury or considerable damage may result if these automatic placement systems
are handled incorrectly.
After you have properly carried out the shut-down of the operating system:
Before all work the machine must be turned off at the main switch and isolated from the mains. In
addition, the compressed air supply must be turned off at the main valve of the compressed air
unit in the machine base.
Danger:
For anyone wearing a heart pacemaker it is not permitted to work near linear motors, as described
in detail in the User Manual and the Service Manual, Chapter "Special Safety Instructions when
working in vivinty of powerful magnetic fields" .
Obey the applicable accident prevention regulations, DIN standards and special safety codes of
your country at all times. DIN EN 60204 must be adhered to during all work inside the machine
base.
Follow the instructions regarding residual voltages in Chapter "Operational Safety".
Comply with regulations on ESDs (see Chapter "Operational Safety").
During the work of service secure the machine conscientiously against other personnel and pre-
vent it from being turned back on without authorization, as described in the User Manual in the
chapter “Locking the Machine”.
There is additional, higher risk of accident when working with the SITEST program.
The SITEST program is only to be started by personnel who are authorized to do so.
1 - 8
SIPLACE CAN Bus Edition 10/2018
8
1.1 History of the document
Version Edition Modification
00194932-01 11/2005 Introduction CAN Test Box
00194932-02 01/2006 Error correction and improve layout
00194932-03 01/2006 New Note for Service connector Chapter 1.4
00194932-04 03/2006 New chapter 1.1 Safety
00194932-05 03/2006 Chapter 1.2 insert part number CAN Bus Test cable
Chapter 1.10.7 Legend DIP Switch/Note
00194932-06 03/2006 Insert new chapter 1.10.7"Exchange the Axis unit version 03 to
version 04 on HF/HF3 machine"
00194932-07 07/2006 Insert new chapter 1.10.9 CAN Bus structure Siplace D4
00194932-08 10/2006 Insert chapter 1.10.9 CAN Bus Structure D1,D2
00194932-09 01/2007 Improved picture CAN Bus signal assignment in chapter 1.3
Improved overview CAN Bus structure HS50/60 in chapter 1.10.2
Note: Siplace D3 machine
Chapter 1.10.9 improved overview CAN Bus Terminator D-ma-
chine
00194932-10 02/2008 New Structure, one chapter 1.10.4 for HF/HF3 and one chapter
1.10.5 for X-Series with new CAN Bus structure for X2, X3, X4
Insert new machine Siplace X4i
00194932-11 04/2008 Error correction in chapter 1.10.10 wrong DIP switch description
for D-series
00194932-12 07/2009 Update CAN Bus structure X4i with A364
New chapter 1.10.11 CAN Bus structure Siplace SX Series
00194932-13 01/2011 New ASM Layout
Update chapter 1.10.11 with Siplace DX-Series and SX4/DX4
00194932-14 05/2011 Complete new structure of the document
New chapter with the description of the Error Frame diagnostic
unit.
00194932-15 06/2013 New chapter 4.12 CAN Bus structure Siplace X-Series S
with X4 S, X4i S and X3 S
Tab. 1.1 - 1 Document history
1 - 9
Edition 10/2018 SIPLACE CAN Bus
9
00194932-16 12/2013 Introduce a chapter for document
Update chapter 3.3 Settings Dip Switch and chapter 4.12 new
CAN Bus structure with CAN Switch on Siplace X-Series S with
X4 S, X4i S and X3 S
New machine type X2-S.
00194932-17 07/2015 Chapter 2.1 Higher-level assembly part number for the CAN Test
Box-->SIPLACE CAN Bus Analysistool
Chapter 3.3 Error Frame Diagnostic unit
Change description for the LED(2)
Note for the DIP-Switch setting on S1.3 -S1.5
New chapter 4.12 CAN Bus structure SX/DX-Series
(from Ma No. N001 May 2015)
New chapter 4.15 X-Series S with new CAN Bus card (CIN Box)
and new CAN Bus structure.
New chapter 4.16 E-Series CAN Bus structure
00194932-18 01/2016 New chapter 4.17 TX-series CAN Bus structure
(since Nov.2015)
00194932-19 02/2017 New chapter 4.13 SX/DX-series CAN Bus structure with MGCU
3-fold (from MA No. P001 June 2016)
New chapter 4.19 TX machine and TXmicron CAN Bus structure
with preparation for the option shuttle (from TA >=500 January
2017)
00194932-20 10/2018 New chapter 4.20 CAN Bus structure TX series V2
Change chapter 2 new CAN Bus test cable (03159250-01 Test-
cable CAN-Bus)
Version Edition Modification
Tab. 1.1 - 1 Document history