DEUKYX-193-4110_G5S2_VOL4.pdf - 第151页
DEUKYX 2-1 1 193-41 10 2.2 Management-Informationsliste Code Anzeigebereich A Anzeigebereich B 18301 T ray (Block2) Close the safety door of T ray , and press a button [READY] of it. When T ray [READY] does not change to…
DEUKYX
2-10193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
18001
Recycling Conveyor
(Block1)
Recycle Conveyor (Block1) is lled up.
18002
Recycling Conveyor
(Block1)
The connection of Recycling Conveyor (Block1) differs from Cmpnt Arranging
Data. Or, it has multi-connection.
18003
Recycling Conveyor
(Block1)
Recycling Conveyor (Block1) is on ready. Please remove parts and resume
production after completion of operation.
18004
Recycling Conveyor
(Block1)
Recycling conveyer is connected to F159. Please be connected to the range of
F105-F157 or F205-F257 again.
18101
Recycling Conveyor
(Block2)
Recycling Conveyor (Block2) is lled up.
18102
Recycling Conveyor
(Block2)
The connection of Recycling Conveyor (Block2) differs from Cmpnt Arranging
Data. Or, it has multi-connection.
18103
Recycling Conveyor
(Block2)
Recycling Conveyor (Block2) is on ready. Please remove parts and resume
production after completion of operation.
18104
Recycling Conveyor
(Block2)
Recycling conveyer is connected to F259. Please be connected to the range of
F105-F157 or F205-F257 again.
18201 Tray (Block1)
Close the safety door of Tray, and press a button [READY] of it. When Tray
[READY] does not change to [ON], press the button [READY] of Feeder.
18202 Tray (Block1) Pallet of Tray is drawn out. Execute zeroing all, and store the pallet.
18203 Tray (Block1) Tray breaking out was detected. Execute zeroing all, and store the pallet.
18204 Tray (Block1) Press [READY] button of Feeder base, and supply the power of Tray.
18205 Tray (Block1) Close the safety door (Center) of Tray, and press [READY] button.
18206 Tray (Block1) Close the safety door (Lower) of Tray, and press [READY] button.
18207 Tray (Block1) Close the safety door (Upper) of Tray, and press [READY] button.
18208 Tray (Block1) Zeroing of Traverse-axis is not nished. Perform zeroing of Tray.
18209 Tray (Block1) Zeroing of Elevator1-axis is not nished. Perform zeroing of Tray.
1820a Tray (Block1) Zeroing of Elevator2-axis is not nished. Perform zeroing of Tray.
1820b Tray (Block1) Pickup miss cmpnt (8 mm) is detected.[B15417]
1820c Tray (Block1) Pickup miss cmpnt (14 mm) is detected.[B15418]
1820d Tray (Block1) Pickup miss cmpnt (28 mm) is detected.[B15419]
1820e Tray (Block1) Pallet Chuck Claw is open.
1820f Tray (Block1) Pallet Error is detected.
18210 Tray (Block1) Magazine 1 (Lower) Shutter on Traverse side is open.
18211 Tray (Block1) Magazine 2 (Upper) Shutter on Traverse side is open.
18212 Tray (Block1) Access detecting Sensor (Right) : Cannot detect Elevator Unit
18213 Tray (Block1) Access detecting Sensor (Left) : Cannot detect Elevator Unit
18214 Tray (Block1) Pick-up miss cmpnt is detected.
18215 Tray (Block1) Traverse axis is not on origin. Please perform zeroing of Tray.
18216 Tray (Block1) Tray is running. Please operate it after completion.
18217 Tray (Block1) Please supply Tray Cmpnt after all zeroing.
18218 Tray (Block1) The supply area magazine has an unsettled palette. Please remove it.
18219 Tray (Block1) A head and a traverse axis interfere it. Please evacuate in a head.
DEUKYX
2-11193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
18301 Tray (Block2)
Close the safety door of Tray, and press a button [READY] of it. When Tray
[READY] does not change to [ON], press the button [READY] of Feeder.
18302 Tray (Block2) Pallet of Tray is drawn out. Execute zeroing all, and store the pallet.
18303 Tray (Block2) Pallet Error of Tray is detected. Execute zeroing all, and store the pallet.
18304 Tray (Block2) Press [READY] button of Feeder base, and supply the power of Tray.
18305 Tray (Block2) Close the safety door (Center) of Tray, and press [READY] button.
18306 Tray (Block2) Close the safety door (Lower) of Tray, and press [READY] button.
18307 Tray (Block2) Close the safety door (Upper) of Tray, and press [READY] button.
18308 Tray (Block2) Zeroing of Traverse-axis is not nished. Perform zeroing of Tray.
18309 Tray (Block2) Zeroing of Elevator1-axis is not nished. Perform zeroing of Tray.
1830a Tray (Block2) Zeroing of Elevator2-axis is not nished. Perform zeroing of Tray.
1830b Tray (Block2) Pickup miss cmpnt (8 mm) is detected.[B15417]
1830c Tray (Block2) Pickup miss cmpnt (14 mm) is detected.[B15418]
1830d Tray (Block2) Pickup miss cmpnt (28 mm) is detected.[B15419]
1830e Tray (Block2) Pallet Chuck Claw is open.
1830f Tray (Block2) Pallet Error is detected.
18310 Tray (Block2) Magazine1 (Lower) Shutter on Traverse side is open.
18311 Tray (Block2) Magazine2 (Upper) Shutter on Traverse side is open.
18312 Tray (Block2) Access detecting Sensor (Right) : Cannot detect Elevator Unit
18313 Tray (Block2) Access detecting Sensor (Left) : Cannot detect Elevator Unit
18314 Tray (Block2) Pick-up miss cmpnt is detected.
18315 Tray (Block2) Traverse axis is not on origin. Please perform zeroing of Tray.
18316 Tray (Block2) Tray is running. Please operate it after completion.
18317 Tray (Block2) Please supply Tray Cmpnt after all zeroing.
18318 Tray (Block2) The supply area magazine has an unsettled palette. Please remove it.
18319 Tray (Block2) A head and a traverse axis interfere it. Please evacuate in a head.
18401
Tray is not ready to
zeroing (Block1)
Execute all zeroing.
18501
Tray is not ready to
zeroing (Block2)
Execute all zeroing.
18601 Warning of wiring error Vacuum Pump 1CB Error
18602 Warning of wiring error Monitor Error of DC load power
18603 Warning of wiring error Beam 1 CB Error Monitor Error
18604 Warning of wiring error Beam 2 CB Error Monitor Error
18701 Feeder Alternate Illegal alternate setup of pattern program. Check the settings.
18702 Feeder Alternate Invalid feeder in alternating. Set feeder valid
18801 XY Origin Offset
Since the data transfer of XY-Origin offset is not completed, please perform
again after waiting for a while (Beam 1).
18802 XY Origin Offset
Since the data transfer of XY-Origin offset is not completed, please perform
again after waiting for a while (Beam 2).
DEUKYX
2-12193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
18901 Feeder communication
Feeder (Block1) is on communication. Please wait for a second, and then
operate again.
18902 Feeder communication
Feeder (Block2) is on communication. Please wait for a second, and then
operate again.
18a01
Library Feed Pitch
check
Library Feed Pitch differs from Feeder. Please check Library and Feeder.
(Block1)
18a02
Library Feed Pitch
check
Library Feed Pitch differs from Feeder. Please check Library and Feeder.
(Block2)
18b01
Library Tape Width
check
Library Tape Width differs from Feeder. Please check Library and Feeder.
(Block1)
18b02
Library Tape Width
check
Library Tape Width differs from Feeder. Please check Library and Feeder.
(Block2)
19001 Support Pin Please move exchange position of support pin.
19002 Support Pin
There is no available nozzle for backup pin exchange. In the case of a multi
function head, please set a Nozzle to No.1 - No.5 of the stocker, and secure a
Nozzle storage space to No.1 - No.5 of the stocker.
19003 Support Pin
Arranging data in current differs from it of Support Pin of current pattern
program. Please set-up the support pin.
19004 Support Pin
When PCB size 216 mm is exceeded, it is impossible to operate if Support pins
of Lane A remain. Please exchange Lane A, or take out it from machine.
19005 Support Pin
It is impossible to do operation for only Lane B because Support Pins of Lane
A remain. Please exchange Lane A, or take out it from machine.
19006 Support Pin
Operation for Lane A is impossible because Support Pins of Lane A have not
been installed. Please exchange Support pins or store them.
19007 Support Pin
It is impossible to do Operation for only Lane A because Support Pins of Lane
B remain. Please exchange Lane B, or take out it from machine.
19008 Support Pin
Support pins of Lane B remain on the base for Support pins of Lane A, so that
it is impossible to do Conveyor width. Please exchange Support pins or store
them.
19009 Support Pin Arrangement of Support Pins interferes in Conveyor. Please retry to arrange it.
1900A Support Pin
“Vacuum/Blower” of Test Operation Mode is set “Disable”. Execute it after
cancelling Test Operation Mode.
1900B Support Pin
An unsettled component or a Support pin was detected (Head1). Please check
the state of Head, and discard the component.
1900C Support Pin
An unsettled component or a Support pin was detected (Head2). Please check
the state of Head, and discard the component.
1900D Support Pin Please exchange Support pins or store them.
1900E Support Pin
PCB Y size and Conveyor Width in Current Program are not equal. Please
change Current Program.
19101 Single-Tray (Block1)
The connection of Single-Tray differs from Cmpnt Arranging Data. Please
connect Single-Tray to Lane No.25 and No.55 Of Feeder cart.
19102 Single-Tray (Block1) Pallet Error of Single-Tray is detected. Please set Pallet to the inside.
19201 Single-Tray (Block2)
The connection of Single-Tray differs from Cmpnt Arranging Data. Please
connect Single-Tray to Lane No.25 and No.55 Of Feeder cart.
19202 Single-Tray (Block2) Pallet Error of Single-Tray is detected. Please set Pallet to the inside.
3012c Operation Requirement Please change enable mode into disable mode. (serial out mode)
30162 Operation Requirement The pattern cannot be switched
30413 Operation Requirement Specify the order No.