DEUKYX-193-4110_G5S2_VOL4.pdf - 第170页
DEUKYX 2-30 193-41 10 3.2 Maschinen-Informationsliste Fehler-Code (HEX) Anzeigebereich A Anzeigebereich B 80c004 Tray turning on Failed in turning on Driver power of T ray (Block2) Magazine2 (Upper). Please conrm the wi…
DEUKYX
2-29193-4110
3.2 Maschinen-Informationsliste
Fehler-Code
(HEX)
Anzeigebereich A Anzeigebereich B
809c01 Motor system error
(System Error : 0xE400) Communication not establish with Servo Amp (XY
Beam).
809c02 Motor system error (System Error : 0xE405) Servo Amp parameter error.
809c03 Motor system error
(System Error : 0xE400) Communication not establish with Servo Amp (Head).
809c04 Motor system error The system error occurred in SSCNET.
809d01
Recycle conveyor
lled up
Recycle conveyor became Full. (Block1)
809d02
Recycle conveyor
lled up
Recycle conveyor became Full. (Block2)
809e01 Automatic Teaching
Please skip it because Automatic modication Teaching is impossible in
Nozzle position of Head1.
809e02 Automatic Teaching
Please skip it because Automatic modication Teaching is impossible in
Nozzle position of Head2.
809f01
Conrm Tray Safety
Cover
There is no magazine. Magazine 1 (Lower).
809f02
Conrm Tray Safety
Cover
Rack shutter of operator side is open. Magazine 1 (Lower)
809f03
Conrm Tray Safety
Cover
Rack shutter of traverse side is open. Magazine 1 (Lower)
809f04
Conrm Tray Safety
Cover
The Magazine is not set correctly. Magazine 1 (Lower)
Check lock lever of magazine.
809f05
Conrm Tray Safety
Cover
There is no magazine. Magazine 2 (Upper).
809f06
Conrm Tray Safety
Cover
Rack shutter of operator side is open. Magazine 2 (Upper)
809f07
Conrm Tray Safety
Cover
Rack shutter of traverse side is open. Magazine 2 (Upper)
809f08
Conrm Tray Safety
Cover
The Magazine is not set correctly. Magazine 2 (Upper)
Check lock lever of magazine.
809f09
Conrm Tray Safety
Cover
Motor Error of Magazine (Lower) is detected.
809f0a
Conrm Tray Safety
Cover
Motor Error of Magazine (Upper) is detected.
80a001 Recognition Error Failed in the recognition of the part. Please retry pickup of the part.
80a002 Recognition Error Nozzle position teaching failure. Check nozzle condition.
80a003 Recognition Error
It failed in the light emitter recognition of the side view camera. Please
conrm the light emitter of the side view camera.
80a101
Reading the Side
view camera sensor
Version
The operation for turning on is invalid. Please do operation again after
turning on completely.
80b001
Automatic Teaching
Error
Failed in the recognition. Carr it out again on the next time. Please carry out
cleaning of a nozzle, cleaning of a reference mark, and re-instruction based
on head rotations.
80b002
Automatic Teaching
Error
The jam for a nozzle was detected (Recognition). Please carry out cleaning
of a nozzle
80c001 Tray turning on
Failed in turning on Driver power of Tray (Block1) Magazine1 (Lower).
Please conrm the wiring of Machine
80c002 Tray turning on
Failed in turning on Driver power of Tray (Block1) Magazine1 (Upper).
Please conrm the wiring of Machine
80c003 Tray turning on
Failed in turning on Driver power of Tray (Block2) Magazine2 (Lower).
Please conrm the wiring of Machine
DEUKYX
2-30193-4110
3.2 Maschinen-Informationsliste
Fehler-Code
(HEX)
Anzeigebereich A Anzeigebereich B
80c004 Tray turning on
Failed in turning on Driver power of Tray (Block2) Magazine2 (Upper).
Please conrm the wiring of Machine
80c101
Tray ACV miss-
placement error (Step)
Error of miss-placement : Tray (Block1) Magazine1 (Lower)
80c102
Tray ACV miss-
placement error (Step)
Error of miss-placement : Tray (Block1) Magazine2 (Upper)
80c103
Tray ACV miss-
placement error (Step)
Error of miss-placement : Tray (Block2) Magazine1 (Lower)
80c104
Tray ACV miss-
placement error (Step)
Error of miss-placement : Tray (Block2) Magazine2 (Upper)
80c201
Tray ACV miss-
placement error
(Magazine)
Tray (Block1) Magazine1 (Lower) Cannot use it in AUTO OPN MODE
(PLACEMENT) because of miss-placement.
80c202
Tray ACV miss-
placement error
(Magazine)
Tray (Block1) Magazine2 (Upper) Cannot use it in AUTO OPN MODE
(PLACEMENT) because of miss-placement.
80c203
Tray ACV miss-
placement error
(Magazine)
Tray (Block2) Magazine1 (Lower) Cannot use it in AUTO OPN MODE
(PLACEMENT) because of miss-placement.
80c204
Tray ACV miss-
placement error
(Magazine)
Tray (Block2) Magazine2 (Upper) Cannot use it in AUTO OPN MODE
(PLACEMENT) because of miss-placement.
80c301
Tray Safety Cover
Lock cleared (Auto
Run)
Cannot clear Lock because Cmpnt shortage is not found on Tray (Block1)
Magazine1 (Lower).
80c302
Tray Safety Cover
Lock cleared (Auto
Run)
Cannot clear Lock because Cmpnt shortage is not found on Tray (Block1)
Magazine2 (Upper).
80c303
Tray Safety Cover
Lock cleared (Auto
Run)
Cannot clear Lock because Cmpnt shortage is not found on Tray (Block2)
Magazine1 (Lower).
80c304
Tray Safety Cover
Lock cleared (Auto
Run)
Cannot clear Lock because Cmpnt shortage is not found on Tray (Block2)
Magazine2 (Upper).
80c401 Nozzle Exchange
There is no nozzle required for production. Please check the following.
1. Existence of Nozzle Stocker, Clamp Condition
2. Nozzle Conguration Data
80c402 Nozzle Exchange
A nozzle cannot be stored. Please check the following.
1. Existence of Nozzle Stocker, Clamp Condition
2. Nozzle Conguration Data
80c403 Nozzle Exchange ODD Noz of Head is stored for storing high-speed Noz.
80c404 Nozzle Exchange Noz is stored due to error in teaching Noz Position.
80c405 Nozzle Exchange Please take down the nozzle stocker.
80c406 Nozzle Exchange
A necessary nozzle is installed in the head that has not been selected.
Please select the back and forth block, and execute the nozzle exchange.
80c501
Overall Setup
(Exchange support pin)
Pattern Program data set the support pin as [No exchange], so that skipped it.
80c502
Overall Setup
(Exchange support pin)
Noz is not for Support Pin Exchange, so that it is stored.
80c503
Overall Setup
(Exchange support pin)
There is no available nozzle for backup pin exchange. In the case of a multi
function head, please set a nozzle to No.1 - No.7 of the stocker.
80c504
Overall Setup
(Exchange support
pin)
Conveyor Width is stopped at the position for exchanging support pins
because the Support pins of Lane A are stored. Please take out Support
pins from machine, or install Conveyor Width after setting them at production
position.
DEUKYX
2-31193-4110
3.2 Maschinen-Informationsliste
Fehler-Code
(HEX)
Anzeigebereich A Anzeigebereich B
80c505
Overall Setup
(Exchange support pin)
Support pins is not inserted correctly. Check the insertion of support pins at
"Setup"-"Sprt-Pins"-"Sup.Pins Insert Check", please insert normally.
80c601
Overall Setup
(Conveyor width setup)
Pattern Program data set the conveyor width as [No Setup]. So that skipped
it.
80c701
Nozzle Level Offset
Teaching
All E/NR from side view camera sensor is detected. Please conrm it
because there is a possibility that ODD Noz is placed.
80c702
Nozzle Level Offset
Teaching
Could not do Teaching because Noz for measurement on Head1 is not set.
80c703
Nozzle Level Offset
Teaching
Could not do Teaching because Noz for measurement on Head2 is not set.
80c704
Nozzle Level Offset
Teaching
The Length of measured Noz is out of Allowable Range. Please conrm the
Noz of Head.
80c801 Cutter Auto Reset Cutter Auto Reset of Device (Block1) is executed. (The 1st)
80c802 Cutter Auto Reset Cutter Auto Reset of Device (Block2) is executed. (The 1st)
80c803 Cutter Auto Reset Cutter Auto Reset of Device (Block1) is executed. (The 2nd)
80c804 Cutter Auto Reset Cutter Auto Reset of Device (Block2) is executed. (The 2nd)
80c805 Cutter Auto Reset Cutter Auto Reset of Device (Block1) is executed. (The 3rd)
80c806 Cutter Auto Reset Cutter Auto Reset of Device (Block2) is executed. (The 3rd)
80c901
Recycling Conveyor
(Block1)
Recycling Conveyor (Block1) is on ready. Please remove parts and resume
production after completion of operation.
80ca01
Recycling Conveyor
(Block2)
Recycling Conveyor (Block2) is on ready. Please remove parts and resume
production after completion of operation.
80cb01
Undetermined Tray
Comp. (Block1)
An undetermined component is detected.
80cc01
Undetermined Tray
Comp. (Block2)
An undetermined component is detected.
80d001
Counter Board
synchronization gap
detection (Head1)
The synchronization gap of Counter Board was detected (X-axis).
80d002
Counter Board
synchronization gap
detection (Head1)
The synchronization gap of Counter Board was detected (Y-axis).
80d101
Counter Board
synchronization gap
detection (Head2)
The synchronization gap of Counter Board was detected (X-axis).
80d102
Counter Board
synchronization gap
detection (Head2)
The synchronization gap of Counter Board was detected (Y-axis).
80d201
Side view camera
synchronization gap
detection (Head1)
The synchronization gap of Side view camera was detected. Please conrm
the connector of the encoder cable.
80d301
Side view camera
synchronization gap
detection (Head2)
The synchronization gap of Side view camera was detected. Please conrm
the connector of the encoder cable.
80e001
Noz Selection
axis position offset
teaching
The 1st Re-trial for Noz Selection axis position offset teaching started.
80e002
Noz Selection
axis position offset
teaching
The 2nd Re-trial for Noz Selection axis position offset teaching started.
80f001 Auto Opn.Mode Start Auto Opn.Mode.