DEUKYX-193-4110_G5S2_VOL4.pdf - 第162页
DEUKYX 2-22 193-41 10 2.2 Management-Informationsliste Code Anzeigebereich A Anzeigebereich B 0d3d01 Comp Height Ovr (head1) This function cannot use. Beause of comp height over . 0d3d02 Comp Height Ovr (head2) This func…
DEUKYX
2-21193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
0d3204
Feeder Base Up/Down
Operation Restrictions
(Block1)
Please check that Recycle Conveyor is not carried on a feeder base, and
perform UP operation of a base again.
0d3301
Feeder Base Up/Down
Operation Restrictions
(Block2)
In order to make a feeder base go up and down, please remove the stock stick
unit on a base.
0d3302
Feeder Base Up/Down
Operation Restrictions
(Block2)
Please check that the stock stick unit is not carried on a feeder base, and
perform UP/DOWN operation of a base again.
0d3303
Feeder Base Up/Down
Operation Restrictions
(Block2)
Please set “a feeder connection check / feeder serial communication” of test
operation as “Disable” for a unit check.
0d3304
Feeder Base Up/Down
Operation Restrictions
(Block2)
Please check that Recycle Conveyor is not carried on a feeder base, and
perform UP operation of a base again.
0d3401
And without substrate
transfer step without
mounting
Because there is no step installed, that does not provide a substrate transfer,
can not operate.
Simple or cancel the skip, please go to the substrate transfer.
0d3501
High Speed Head ux
coating impossible
Because you do not want to use the side view camera, can not high speed dip.
Verify the following settings, please change.
System setting : Side view camera : Use
Test run :No parts : Detected
0d3601
The appointed external
communication
Please clear the P-OUT mode.
0d3701 VM Data Error Abnormalities occurred in data expansion. Please inspect with a tester again.
0d3801
The cart for
independent production
(Block1) Test operation When you do not carry out a feeder connection check,
please raise the feeder base which carries out production use.
0d3802
The cart for
independent production
(Block2) Test operation When you do not carry out a feeder connection check,
please raise the feeder base which carries out production use.
0d3901
Unit exchange of Tray
Feeder
Please restart.
0d3a01 Comp. existence check Please turn off the Valve.
0d3b01 Check for a function The nozzle is not applicable to this operation.
0d3901
Uninstalled Brush Unit
(Block1)
Please put a brush unit on F107-F153.
0d3902
Uninstalled Brush Unit
(Block1)
Please put a brush unit on F107-F119.
0d3903
Uninstalled Brush Unit
(Block1)
Please put a brush unit on F107.
0d3904
Uninstalled Brush Unit
(Block2)
Please put a brush unit on F207-F253.
0d3905
Uninstalled Brush Unit
(Block2)
Please put a brush unit on F207-F219.
0d3906
Uninstalled Brush Unit
(Block2)
Please put a brush unit on F207.
0d3c01 Pin Recog Light (head1) The high speed head cannot move to the pin recog light.
0d3c02 Pin Recog Light (head2) The high speed head cannot move to the pin recog light.
0d3c03 Pin Recog Light (head1) The comp size is over the pin recog light spec.
0d3c04 Pin Recog Light (head2) The comp size is over the pin recog light spec.
DEUKYX
2-22193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
0d3d01 Comp Height Ovr (head1) This function cannot use. Beause of comp height over.
0d3d02 Comp Height Ovr (head2) This function cannot use. Beause of comp height over.
0d3e01
Full detection of trash
box for component
(Block1)
Trash box for component become full. Please clean trash box for component.
0d3f01
Full detection of trash
box for component
(Block2)
Trash box for component become full. Please clean trash box for component.
DEUKYX
2-23193-4110
3. Maschineninformation
3. Maschineninformation
3.1 „Machine Information“-Bildschirm
Während des Betriebs werden auf dem Bildschirm Maschineninformation die
unterschiedlichsten Informationen angezeigt.
Hinweis
Die Maschine wird über die Anzeige nicht gestoppt.
[1]
[6]
[3]
[2]
[4] [5]
F4B3
[1] Maschinen Information-Code
In diesem Textfeld wird der Maschinen-Informationscode angezeigt.
[2] Anzeigebereich A
Hier wird die Überschrift der Maschineninformation angezeigt.
[3] Anzeigebereich B
Hier werden die Details zu der Maschineninformation angezeigt.
[4] [Clear Alm]-Taste
Mit dieser Taste wird der Alarmton stumm geschaltet.
[5] [OK]-Taste
Mit dieser taste wird der Bildschirm „Machine Information“ geschlossen.
[6] Fehleranzeige
Wenn eine Benachrichtigung über einen Fehler, der am Abdeckband
aufgetreten ist (Fehlercode 0x802401), erfolgt, werden die Feeder-Nummer
und ein entsprechendes Bild angezeigt. (Drei Dinge können von links nach
rechts angezeigt werden.)