DEUKYX-193-4110_G5S2_VOL4.pdf - 第154页
DEUKYX 2-14 193-41 10 2.2 Management-Informationsliste Code Anzeigebereich A Anzeigebereich B 30501 Misidentication a type of T ray The connected T ray unit (Block1) doesn’t match settings of Device. Please conrm a typ…
DEUKYX
2-13193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
30416 Operation Requirement
ACV server does not pass the authorization. Please retry to connect to server
on a screen [UNIT ADJ]-[ACV Set].
3041C Operation Requirement
ACV Check Error. Component ID on the feeder is not same as one specied by
current program.
30420 Operation Requirement
Communications with the ACV server is impossible. After conrming the ACV
server, please retry to perform it. [MAINT]-[UNIT ADJ]-[ACV ADJ].
30421 Operation Requirement
ACV server is out of condition. Check the ACV server. Check HDD capacity,
database breakage, the condition of each module and communication between
severs.
30430 Operation Requirement
Can not detect Feeder cart (Block1). Please set Feeder cart to the inside.
[B0910, B0911]
30431 Operation Requirement
Can not detect Feeder cart (Block2). Please set Feeder cart to the inside.
[B0910, B0911]
30432 Operation Requirement
The connector of the feeder base (Block1) is not connected to the main body,
so that please connect it. [B0916]
30433 Operation Requirement
The connector of the feeder base (Block2) is not connected to the main body,
so that please connect it. [B0916]
30440 Operation Requirement The Safety cover is open. Please close it.
30441 Operation Requirement
It is impossible to do Pass Operation without Cart because func of Traceability
is valid. Please restart after setting Option invalid.
30442 Operation Requirement
It cannot run because a simple Cover locked. First, set Stage ready OFF, then
set Stage ready ON.
30450 Operation Requirement To run is impossible by start protect.
30451 Operation Requirement
Cannot start to run because the output folder on server is disconnected. Please
check output folder setting and the server status of output folder.
30452 Operation Requirement
When “”Lne Operatin System”” is specied besides [LISA], the[Enable (In
Order)] setting cannot be done to “”B.C.D.PpChg-P.P.Chng.Func set””.
30453 Operation Requirement
When “”Lne Operatin System”” is specied besides [LISA], the[Enable (BS)]
setting cannot be done to “”B.C.D.PpChg-P.P.Chng.Func set””.
30454 Operation Requirement
To run is impossible by shortage of components. (Component Remain Stop
Mode: PCB) Please supply the components.
30455 Operation Requirement
To run is impossible by shortage of components. (Component Remain Stop
Mode: Product PCB) Please supply the components.
30456 Operation Requirement
Since the [PCB Finishing Position] data of a Crnt.Prgm is a nish setup
[Sequence], it cannot start (Component Remain Stop Mode). Please set to the
[Output] or the [Input]
30457 Operation Requirement Please start Auto Opn after Comp library data updating.
30458 Operation Requirement The component skip is set up. Please choose other steps.
30459 Operation Requirement
Cannot start to run because the machine event output server is disconnected.
Please check machine event output setting and the server status of output.
30460 Operation Requirement
Moisture deadline of component has passed.
Please replace the component in the moisture deadline.
30461 Operation Requirement
Customer system cooperation: The machine is communicating the non-output
information of the traceability information. Please wait for a second, and then
operate again.
30462 Operation Requirement
AOI feedforward function: The machine is communicating the non-output
information of the Inspection information. Please wait for a second, and then
operate again.
30463 Operation Requirement
Cannot start to run because a LCR check is uncompleted. Please check a
target component in a LCR check screen.
DEUKYX
2-14193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
30501
Misidentication a type
of Tray
The connected Tray unit (Block1) doesn’t match settings of Device. Please
conrm a type of tray unit, and set it on unit exchange screen.
30502
Misidentication a type
of Tray
The connected Tray unit (Block2) doesn’t match setup of Device. Please
conrm a type of tray unit, and set it on Unit Exchange Screen.
30601
Conrmation of the
position of Noz Stocker
Cannot use Noz stocker from the second to the forth line when full tray is used.
Please set the location of Noz stocker of Device (Block1) on Unit exchange
Screen.
30602
Conrmation of the
position of Noz Stocker
Cannot use Noz stocker from the second to the forth line when full tray is used.
Please set the location of Noz stocker of Device (Block2) on Unit exchange
Screen.
30603
Conrmation of the
position of Noz Stocker
Cannot use Noz stocker from the second to the forth line when full tray is used.
Please conrm the location of Noz stocker of Device (Block1).
30604
Conrmation of the
position of Noz Stocker
Cannot use Noz stocker from the second to the forth line when full tray is used.
Please conrm the location of Noz stocker of Device (Block2).
30701
Conrmation of 2D Bar
code Data
Mark No. of Operating Parameter/2D Bar Code data is specied as All Skip (0).
Please specify proper Mark No.
30801
Detect nozzle coming
off multi-functional
stocker
Machine (Block1) Detected that nozzle has come off the multi-functional
stocker of the 1st line.
30802
Detect nozzle coming
off multi-functional
stocker
Machine (Block1) Detected that nozzle has come off the multi-functional
stocker of the 4th line.
30803
Detect nozzle coming
off multi-functional
stocker
Machine (Block2) Detected that nozzle has come off the multi-functional
stocker of the 1st line.
30804
Detect nozzle coming
off multi-functional
stocker
Machine (Block2) Detected that nozzle has come off the multi-functional
stocker of the 4th line.
30901
Head nozzle dropped
detect
Please lock the main safety cover. Please perform all-zeroing when the main
safety cover has already been locked.
50201
Conrmation of PCB
existence
Remove PCB from the conveyor. Please delete the PCB memory information
on the edit screen if it remains.
50202
Conrmation of PCB
existence
PCB is detected from Input position when Finish mode is set [Output]. Please
PCB from conveyor.
50203
Conrmation of PCB
existence
PCB is detected from Output position when Finish mode is set [Input]. Please
PCB from conveyor.
50204
Conrmation of PCB
existence
PCB is detected from Inlet sensor of input conveyor. Please remove PCB.
50205
Conrmation of PCB
existence
The operation mode of Lane A is set [STOP]. Please remove PCB when not
transferred.
50206
Conrmation of PCB
existence
The operation mode of Lane B is set [STOP]. Please remove PCB when not
transferred.
50207
Conrmation of PCB
existence
There is a possibility that there are 2 sheets of PCB on the input conveyor.
Please remove PCB from Deceleration Sensor, or move it to Stop sensor, or
delete the PCB memory information.
50208
Conrmation of PCB
existence
There is a possibility that there are 2 sheets of PCB on the input conveyor
in Lane A. Please remove PCB from Deceleration Sensor, or move it to Stop
sensor, or delete the PCB memory information.
50209
Conrmation of PCB
existence
There is a possibility that there are 2 sheets of PCB on the output conveyor
in Lane B. Please remove PCB from Deceleration Sensor, or move it to Stop
sensor, or delete the PCB memory information.
DEUKYX
2-15193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
5020a
Conrmation of PCB
existence
There is a possibility that there are 2 sheets of PCB on the shuttle conveyor in
input side. Please remove PCB from Deceleration Sensor, or move it to Stop
sensor, or delete the PCB memory information.
5020b
Conrmation of PCB
existence
There is a possibility that there are 2 sheets of PCB on the shuttle conveyor in
output side. Please remove PCB from Deceleration Sensor, or move it to Stop
sensor, or delete the PCB memory information.
5020c
Conrmation of PCB
existence
There is PCB on the input sensor of Lane A. Please return PCB to the input
conveyor and run it.
5020d
Conrmation of PCB
existence
There is PCB on the input sensor of Lane B. Please return PCB to the input
conveyor and run it.
5020e
Conrmation of PCB
existence
There is PCB on the input sensor. Please return PCB to the input conveyor and
run it.
5020f
Conrmation of PCB
existence
There is no PCB in the machine. Please position a PCB.
50210
Conrmation of PCB
existence
Please put PCB on the positioning conveyor, and start it.
50211
Conrmation of PCB
existence
Please remove PCB from input position. Cutout PCB cannot be transferred
from input position.
50212
Conrmation of PCB
existence
Please remove the substrate at the upstream position. The substrate for weight
to exceed 2.5 kg cannot be transported simultaneously.
50213
Conrmation of PCB
existence
Please remove the substrate at A lane upstream position. The substrate for
weight to exceed 2.5 kg cannot be transported simultaneously.
50214
Conrmation of PCB
existence
Please remove the substrate at B lane upstream position. The substrate for
weight to exceed 2.5 kg cannot be transported simultaneously.
50215
Conrmation of PCB
existence
After a PCB disappears from the input conveyor of output machine, please
perform (PCB clip lump prevention).
Please switch on a power supply, when the power supply of output machine is
not on.
50216
Conrmation of PCB
existence
Please cancel positioning of a PCB and perform in the state where there is no
PCB.
50220
Conrmation of PCB
existence
2 PCB are between the input conveyor and the upstream position. Take PCB in
a one side.
50221
Conrmation of PCB
existence
A stop place of a PCB is unsettled. Please establish PCB memory information.
50222
Conrmation of PCB
existence
A PCB is on the upstream position stop sensor. Please put a PCB in the
location an upstream stop sensor doesn’t turn on.
50223
Conrmation of PCB
existence
It is not possible to operate, because there is a PCB in the upstream position.
50224
Conrmation of PCB
existence
Please put a P.C.B. in the location a deceleration sensor of a input conveyor
turns on.
50301
Conrmation of
Firmware version
Firmware of transfer driver is not the latest version. Please update it.
50401 Manual transfer
PCB (X > 260 mm) which is set by PP data is unable to be taken in Input
Position.
50402 Manual transfer
Please operate after removing PCB from output conveyor. There is a possibility
of pushing and rising with Stopper.
50403 Manual transfer
It is impossible to take from Sensor Detection of Input Position. Please put
PCB on Input Conveyor, or move it to Output position in Recovery Menu.
50404 Manual transfer
PCB (X > 260 mm) which is set by PP data is unable to be taken in Input
Conveyor.
50405 Manual transfer
There is PCB on Deceleration Sensor of Input Conveyor. There is a possibility
that PCB is inserted.