00198502-02_VD_SIPLACE_Pro_15.1_R18-1_DE_EN.pdf - 第18页

SIPLACE Pro 15.1 (R 18 - 1) / V ersion Description 05/2018 Edition 18 5.3 " The Hermes Standard " – New Communicat ion Protocol " The Hermes Standard " i s a new communicati on protocol for SMT assemb…

SIPLACE Pro 15.1 (R18-1) / Version Description 05/2018 Edition

5 Features of SIPLACE Pro 15.0

If not differently described, the features of the previous SIPLACE Pro versions are contained in

SIPLACE Pro 15.0. The main features of SIPLACE Pro 15.0 are listed below.

NOTICE

Detailed information on the individual functions can be found in the Online Help for

SIPLACE Pro.

5.1 New Fixed Rail Positions

Some fixed rail positions on SIPLACE TX-series placement machines do not match the

correspondent positions on other SIPLACE placement machines (SX / X / X S / DX / CA series).

For compatibility reasons, the following changes have been made in SIPLACE Pro:

– On SIPLACE TX-series placement machines, the existing fixed rail positions 268.0 and 281.0

have been renamed to 268.0 SMEMA and 281.0 SMEMA.

– On the other SIPLACE placement machines, the fixed rail positions 268.0 SMEMA and 281.0

SMEMA have been added to the existing positions 268.0 and 281.0. The new positions should

be used in mixed lines with SIPLACE TX-series placement machines.

5.2 Making Equal Cycle Times for Left and Right Lane

The procedure for borrowing performance between the placement areas has been improved. It is

now possible to achieve the same cycle time for both board sides if the top and bottom side of a

board shall be placed within one line.

Usually, this will be used if the board top and board bottom sides have a different amount of

placements. One board would be finishing clearly earlier than the other board. To compensate this

behavior this new feature will help.

For this, the two board sides have to be inserted in one recipe and each board side has to be

assigned to one side of the line respectively (left / right). Additionally, the Make equal cycle times

for left and right lane option has to be enabled in the Recipe Editor.

The optimizer will use the asynchronous placement areas to make a kind of balancing between the

two boards. In the result view, the two board sides of the recipe are displayed together. The cycle

times of the two board sides are displayed in different colors.

SIPLACE Pro 15.1 (R18-1) / Version Description 05/2018 Edition

5.3 "The Hermes Standard" – New Communication Protocol

"The Hermes Standard" is a new communication protocol for SMT assembly lines that can be used

alternatively to the electrical SIPLACE SMEMA interface. With this protocol, more information can

be transferred with the board down the line like unique board Ids, barcodes, conveyor speed, board

length / width / thickness. All this information can be transferred down the complete line, without

any interruption. Up to now, this was only possible within a SIPLACE SMEMA cluster. If all devices

in the line support "The Hermes Standard", whispering down the line is possible within "The

Hermes Standard" cluster as it is within the SIPLACE SMEMA cluster.

"The Hermes Standard" can be used on all placement machines supported by station software

version ≥ 711. Please refer to the station software Version Description, item no. [00198500-xx].

It is also supported that the line is divided for example into two "The Hermes Standard" clusters, if

other devices in the line do not support "The Hermes Standard".

A button has been added to the Line Editor in SIPLACE Pro Desk, to all production line editors

(e.g. Setup Editor, Recipe Editor, Job Editor) and to the graphical line view in the Line Control GUI

with which the user can hide or show generic devices in the graphical line view.

"The Hermes Standard" connection configuration has been added to the Line Editor in which the

devices are configured (printers, generic devices, process lens devices and placement stations).

Figure 5-1: "The Hermes Standard" connection configuration

The user can only configure "The Hermes Standard" device connections to the next device. The

configuration of the connection to the previous device is displayed read-only, as this configuration

is edited in the respective editor of the previous device.

The Use 'The Hermes Standard' check box specifies whether the connection shall use "The

Hermes Standard" protocol. If not enabled, the SIPLACE SMEMA protocol will be used.

In the Line Control GUI, the new line view 'The Hermes Standard' connection View can be

selected. In this view, the user can check and download "The Hermes Standard" device connection

configuration. Additionally, a report can be created and printed.

Restrictions

– No support for stations with shuttle.

– No support for devices with IPv6 addresses.

SIPLACE Pro 15.1 (R18-1) / Version Description 05/2018 Edition

5.4 Line Configuration with Inspection Systems and AOI Devices

Inspection Systems have been added to the Devices of Line Tree View in the Line Editor. Here

the user can create solder paste inspection devices. Currently, only ASM Process Lens is

supported. IP address, host name and software version can be edited.

The Custom generic line device has been extended by two new attributes: Manufacturer (name of

the manufacturer of the device) and Equipment ID (Id of the machine / serial number).

The existing generic line device type, containing Undefined and AOI has been extended by the

following new types:

AOXI, AXI, ClassificationArea, RepairArea, PlacementMachine, Printer, SPI, Oven.

5.5 New Placement Force – Very Low Force in Placement, Pickup and

Dipping Processes

The new very low force state has been added to SIPLACE Pro.

In the Handling tab of the Component Shape Editor, the force state for placement, pick-up and

dipping can be set in a drop-down menu:

– Standard: the standard force is used.

– Manual: the user can enter own values.

– Very low: the very low force state is enabled.

The very low force state can only be used for the following placement heads:

C&P20 M2, C&P20 P and (from R18-1) C&P20 P2.

5.6 SEMO CRF80 – New Tape Feeder

The new SEMO CRF80 tape feeder from the SEMO company is supported by SIPLACE Pro and

occupies seven tracks on the X-table. The feeder is distributed directly by the manufacturer.

5.7 External Barcode Reader in the Middle of the Line

External barcode readers can now be used in front of any placement machine in the line together

with the Board Gate Keeper. The Board Gate Keeper can be defined as preceding whisperer of

any station, e.g. the third station in the line.

Example:

The line consists of three placement machines. In front of the line and between the second and

third station there is a conveyor with an integrated board barcode reader. These readers shall

be used for traceability purposes and be connected with Traceability via the Board Gate

Keeper.

If the Board Gate Keeper shall be configured as preceding whisperer for both the first and the third

station, the Use station Setting has to be set in the Setup Editor for the line.