00198502-02_VD_SIPLACE_Pro_15.1_R18-1_DE_EN.pdf - 第22页
SIPLACE Pro 15.1 (R 18 - 1) / V ersion Description 05/2018 Edition 22 WPC5 / WPC 6 – C omponents up t o a height of 30mm can be placed with a f orce of 70N with t he WPC5 as of serial number 1485 an d the WPC6 as of seri…
SIPLACE Pro 15.1 (R18-1) / Version Description 05/2018 Edition
21
6 Restrictions
In the following, existing restrictions in SIPLACE Pro are described.
Miscellaneous
– 10-fold and 15-fold stick magazines cannot be combined on the same linear feeder.
– SIPLACE Pro object names (e.g., recipe) must not exceed 125 ASCII characters (including
folder names).
– If various users optimize the same job at the same time, the job which was most recently
completed successfully will overwrite all corresponding recipes.
– The board panel hierarchy must not exceed 10 levels.
– The object folder hierarchy must not exceed 10 levels.
– The operator must manually place manual tray carriers (Carrier 30, Carrier 51, Carrier X,
Carrier SX, Arbitrary Carrier), glue feeders, dip modules, reject conveyors and power
connectors in the initial setup.
– If you work with reduced acceleration for a component shape, this is seen as a "special case"
and the accuracy of 5% for the simulated Optimizer production time will not be achieved.
– The Optimizer does not check if the tray size is bigger than the carrier.
– The WPC can take up to 10 different component types per level. This restriction does not apply
for machines from station software version 7xx.
Station-wise Download
– It is not possible to switch over from dual lane conveyor in asynchronous transport mode to
dual lane conveyor in synchronous transport mode (and vice versa) in combination with station-
wise download.
– When the line control server is rebooted, station-wise downloading will be canceled. After
rebooting, you will need to perform a complete line download to restart production.
– Station-wise downloading supports setup changes in asynchronous dual operation only when
you have the same definition for both lanes.
– Station-wise downloading supports synchronous dual operation as of station software version
704.
ASCII Centroid Import
If component shapes are selected in the ASCII Centroid Import Wizard, all the existing links
between components and component shapes will be overwritten with the imported information.
SIPLACE Pro 15.1 (R18-1) / Version Description 05/2018 Edition
22
WPC5 / WPC6
– Components up to a height of 30mm can be placed with a force of 70N with the WPC5 as of
serial number 1485 and the WPC6 as of serial number C1486 only.
– Components up to a height of 40mm can be placed with the WPC5 as of serial number B3000
and the WPC6 as of serial number C3000.
– Due to the refill module, components > 25mm cannot be positioned on the levels 1 – 3 and
27 – 28 on the WPC6. The levels 4 – 28 will be set up automatically by the SIPLACE Pro
Optimizer. The levels 1 – 3 have to be blocked manually by the operator.
– If a pin picker is installed on the X4i S placement machine, the maximum board length is
410mm.
Binning can be disabled in SIPLACE Vision
– If binning is disabled in SIPLACE Vision, the measuring in the simulation result of the
optimization will probably take a little longer.
External virtual inkspot handling
– Only possible for stations from station software version 707.0 on.
– Physical and virtual inkspot must not be mixed.
– The board must not contain any active inkspots.
Restrictions in the Production Schedule
PCB barcode mode is not supported.
Spring placement process
The board top edge position has to be constant from board to board to allow absolute placement.
Variable board warpages cannot be compensated.
Measuring and changing the component height measured by the component sensor at the
station
– Only for nozzle and component combinations in which the component height is supposed to be
measured with the component sensor.
– The component sensor will not perform any measurement if the component height
measurement is omitted due to SIPLACE Pro rules.
Conveyor Carrier X
– No travel range check.
– No pickup simulation.
– The Conveyor Carrier X uses one track on an X-table virtually. If the real table should be
completely occupied, the operator might have to remove a feeder from the table to create place
for the virtual feeder.
– No I-Placement mode.
– The SIPLACE Pro Optimizer does not consider the time it takes to fill up a tray with
components and change it.
SIPLACE Pro 15.1 (R18-1) / Version Description 05/2018 Edition
23
Heavy Board Mode per board side
– No barcode mode possible.
Board Identification
– The Barcode located under the board property cannot be combined with the board barcode
mode.