9018-18076.pdf.pdf - 第10页
1-6 Site Preparation 1 Site Preparation Process Site Prep Checklist Use this checklist to check off each task as you complete it. Ta b l e 1 - 1 Site pr eparat ion checklist Ta s k Checkl ist Plan ning [ ] Location chose…
Site Preparation Process 1
Site Preparation 1-5
The Site Preparation Process
This section describes the steps of the Keysight system site preparation process.
1 The Site Prep Visit
A Keysight representative will come to your site to discuss what you will need to do to make your
site ready for your system. During this visit, the Keysight representative will review this manual
and answer any questions you may have. This will help you get started preparing your site.
2 Site Planning
The site planning step is crucial. A little effort invested in understanding and planning your
system will save much effort at installation time. Plan your system area using Chapter 2,
Planning. Assign specialists to perform the various tasks. Make a “system plan drawing” that you
and the Keysight representative can use to install your system. If you need help, call your
Keysight representative. Schedule all site preparation activities.
3 Site Plan Implementation
Implement the plan. Use Chapter 3, Structural Requirements through Chapter 8, Receiving and
Moving Instructions and the system plan drawing. Work with your specialists.
4 Site Verification Visit
The site verification visit allows the Keysight representative to review your preparations and
answer any remaining questions. The Keysight representative will check your power to verify that
it is suitable for the system. The Keysight representative will also check your compressed air and
vacuum hookups.
5 Receiving the System
When the system arrives at your site, remove the tri-wall box from the testhead, but do not
remove the system from the pallet. The Keysight representative will remove the testhead from the
pallet. You may inventory the shipment using the enclosed packing list. You may leave the
smaller boxes for the Keysight representative to unpack when the system is installed. You should
move the system to the site where it will be installed, or a safe storage area.
1-6 Site Preparation
1 Site Preparation Process
Site Prep Checklist
Use this checklist to check off each task as you complete it.
Table 1-1 Site preparation checklist
Task Checklist
Planning [ ] Location chosen?
Specialists assigned?
Site Coordinator:
__________________________________________________________
System Administrator:
__________________________________________________________
Structural Specialist:
__________________________________________________________
EMC Specialist:
__________________________________________________________
Environmental Specialist:
__________________________________________________________
Electrical Specialist:
__________________________________________________________
Vacuum Specialist:
__________________________________________________________
Compressed Air Specialist:
__________________________________________________________
Communications Specialist:
__________________________________________________________
[ ] Schedule Created:
Structural Requirements [ ] Floor suitable?
[ ] Room to move the big box? If not, do you have a place to unpack it?
[ ] Storage sufficient?
RF Attenuation Requirements [ ] Required to meet EMC directives?
[ ] Additional attenuation sufficient?
Environmental Requirements [ ] Air quality suitable?
[ ] Ambient temperature suitable?
[ ] Cooling sufficient?
[] Humidity suitable?
[ ] Electromagnetic environment suitable?
Site Preparation Process 1
Site Preparation 1-7
Power Requirements System Power
What power option is your system? Opt. _______________
[ ] AC mains power verified?
[ ] Mains disconnect installed?
[ ] Do you need to install power conditioning equipment?
[ ] Do you need to install a new transformer?
[ ] What system drop wire size is required? Wire Size ____________
[ ] What system drop breaker size is required? Breaker Size ____________
[ ] Power cable installed for mains?
Connect Mains Power
[ ] Power installed to system?
Convenience Outlet Power
[ ] Testhead strip printer?
[] Testhead server?
Compressed Air and Vacuum
Requirements
[] Compressed air line installed?
[ ] Vacuum plan done?
[ ] How many solenoids needed? _____________
[ ] Vacuum equipment installed?
Networking [ ] LAN cabling installed?
The i3070 communicates with other systems via IEEE 802.3 Local Area Networking. All the necessary
software and licensing comes with the system, but the customer is responsible for installing the
external LAN cabling to the i3070.
The internal testhead LAN within each i3070 system — which includes the System Card and Module
Control Card in each module — is identical between systems. However, the hardware address for
each System Card and Module Control Card is unique. The hardware address is assigned at the
factory and is marked on each card.
The remaining items go beyond site preparation, but must be completed before installation
Receiving and Moving Instructions [ ] Insurance coverage arranged for arrival?
[ ] System inspected for physical damage?
[ ] Shipment inventoried?
[ ] Equipment moved to installation site?
[ ] Testhead unpacked (tri-wall box removed, but not removed from the pallet). The Keysight
representative will unpack the smaller boxes and move the system as part of installation.
Table 1-1 Site preparation checklist (continued)
Task Checklist