00192485-02.pdf - 第40页

40 ’ Single functions PCB transport 1 ’ menu This m enu is us ed for checkin g and se tting the func tion modules of the PCB convey or . If th e twin conve yor option is installed, th e Single fun ctions PCB transp ort 2…

Then click on OK.

PLEASE NOTE

Make sure that the nozzle magazines are always full.

Confirm one Produce the desired nozzle configuration in the magazine

magazine indicated by the arrow.

To do this move the cyan bar in the list box to the appropriate line.

Click on ‘Confirm one magazine’. The desired and actual values must

tally.

Confirm all Once you have set up the nozzles in every magazine as desired, click on

magazines ‘Confirm all magazines’. The desired and actual values of all magazines

must tally.

‘Segments’ display box

Seg Segment number, up to 12

Actual Displays the nozzle type set up for each segment.

Buttons in the ‘Revolver head’ box

Return all Returns all the nozzles on the revolver head to the appropriate magazine

nozzles of the nozzle changer.

Reject all Throws all the nozzles on the revolver head into the reject bin.

nozzles

’Single functions PCB transport 1’ menu

This menu is used for checking and setting the function modules of the

PCB conveyor. If the twin conveyor option is installed, the Single functions

PCB transport 2 menu will be activated. The same functions as with PCB

transport 1 will then be available to you.

NOTE

To move the gantries, close the covers and then press the start button. All

gantry and head axes will move at low speed.

Buttons in the ‘Processing area 1’ and ‘Processing area 2’ boxes

The next three menu options act in the same way as a toggle switch.

The following menu options act in the same way as a switch (ON/OFF)

when they are clicked.

Ceramic substrate Click on the ’Ceramic substrate centering’ button to activate or

centering (option) deactivate clamping in order to center the substrate.

Activate clamping Click on the ’Activate clamping’ button to turn clamping on or off.

Activate stopper Click on the ’Activate stopper’ button to move the stopper in or out.

PCB to proc. conv. The PCB is transported from the input conveyor (IC) or intermediate con-

veyor (IC) to processing conveyor 1 (PC1) or processing conveyor 2

(PC2), where it is stopped and clamped in place.

PCB to interm. conv. The PCB is transported from processing conv. 1 (PC1) to the intermediate

conveyor (IC), where it is stopped and clamped in place.

PCB to output conv. The PCB is transported from processing conveyor 2 (PC2) to the output

conveyor (OC).

‘Sensor state’ box

Update sensor This menu option is used to check the statuses of the ultrasonic sensors.

IC/PC1/IC/PC2/OC on the input, placement, intermediate or output conveyor:

1 = has responded

0 = has not responded

‘Conveyor’ box

High Provides the option of setting different transport

speed speeds.

PLEASE NOTE

Make sure that there are no PCBs on the conveyor belts. The input

conveyor belt only runs at high speed.

On Starts the conveyor belts. The following dialog box appears.

Click on OK in the dialog box to end the operation.

Update Click on this button to check whether a PCB was removed

PCB status during transportation. If a PCB was removed, it is cleared from the display

and the stored data.

’PCB conveyor width’ menu

This menu is used for measuring and adjusting the conveyor belt width.

CAUTION

Make sure there are no boards on the conveyor belts when you adjust the

conveyor belt width.

‘Measure width’ box

Measure width again Used to display, measure and save the width of the PCB conveyor.

Enter width again … Click on this button to open a box for entering the PCB conveyor width.

For the single conveyor, you can enter a width between 50 and 460 mm.

The possible values range from 50 mm to 216 mm for the dual conveyor.