00198235-01_VD_710.0_R16-2_DE_EN.pdf - 第29页

Station S oftware 71 0.0 (R16 - 2) / Version Descript ion 12/2016 Edition 29 709.1 SP2 Error n o. Error de scriptio n D1 - 129688701 CA4: the z placem ent position was 5.55 mm below the chuck / carrier surfac e. D1 - 129…

Station Software 710.0 (R16-2) / Version Description 12/2016 Edition

D1-131921801 If a program with an incomplete component shape and a placement position

that had to be taught was downloaded, the machine started with the teaching

of the placement position even though the component shape had not been

taught.

D1-131949317 After a placement with 70N the machine stopped without error message.

D1-132005405 eSW: error message 30560 Could not detect that the valves on

the valve terminal closed led to a software hang-up.

D1-132028101

D1-131880701

D1-131929707

D1-131985201

D1-132028173

D1-132541001

eSW: the machine stopped with error message 40023 CAUTION: Do not

move gantry! Segment is down.

D1-132146101 eSW: during dry run the machine stopped with error message 40020

Unknown placement state.

D1-132430801 During production, the error 32602 The software has stopped

unexpectedly. Shut down Windows, then restart the station.

occurred.

D1-132508593 Could not calibrate the chuck fiducial position.

D1-132542701 The machine stopped with error message 32590 Possible collisions

with high components

D1-132564701 Although the manual barcode input was deactivated in SIPLACE Pro, it was

still allowed at the station.

D1-132595901 The "single component tracking" for the SWS did not write the board barcode

into the trace file.

D1-132598506 After having opened one cover to change the reel, the machine did not start

again.

D1-132650401 The GUI hung up after a JTG hardware problem.

D1-133060801 Calibrating processing area 2 led to error message 33450 cannot move

calibration plate

D1-133198601 The picture to control the defect position was not displayed when a yellow

board was reported.

D1-133227101 When a component should be picked up by the Twin head, the error message

30341 Position is out of range

occurred.

D1-133265101 Error messages 42416 Move plausibility failure and 42419

Invalid time stamps error

were displayed.

D1-133678341 The board view did not display the placement position anymore.

D17845-11307 The machine could not pick up components from the feeder during normal

production.

D18149-4401

D18149-4501

During production the machine stopped sometimes but the GUI still displayed

production status and no error message.

D18171-10932 Both signal lamps were flashing when there was a track error on one table.

Table 8-2: Corrected errors station software 709.1 SP2 Hotfix 1

Station Software 710.0 (R16-2) / Version Description 12/2016 Edition

709.1 SP2

Error no. Error description

D1-129688701 CA4: the z placement position was 5.55 mm below the chuck / carrier surface.

D1-129846501

D1-129969301

Sudden hang up of station software while board was moving in.

D1-129996049 The calibration of the nozzle changer failed.

D1-130020901 Machines stopped after the download of a recipe with a few changes.

D1-130023381 The Teaching of components GUI and the Vision dump view were not

translated into English and Chinese.

D1-130103401 The setup download was sporadically not accepted.

D1-130157701 eSW: during dry run the machine stopped with error message 40020

Unknown placement state

D1-130240801 Sporadically, the production did not start after the program download.

Table 8-3: Corrected errors station software 709.1 SP2

709.1 SP1

Error no. Error description

D1-114875049 eSW: The machine stopped with different error messages due to CIN box

problems.

D1-125773701 Vision: Ball import did not work correctly.

D1-127133701 Vision: the chuck fiducials could not be measured because a wrong DIPF

description was used.

D1-127531101 eSW: Error message: 32564 Machine has stopped: Cannot set

configuration of conveyor.

D1-127554148

D1-127626412

D1-127643301

D1-127697501

D1-128590353

Vision: The calibration of the Twin or CPP head was stopped with an error

message.

D1-128114565 CLI calculated a wrong number of remaining boards.

D1-128582885 Conveyor control did not fit after recovering conveyor data.

D1-128663401 Vision: The PIN 1 recognition from above did not work. The component could

not be taught.

D1-129343001 eSW: Within the SX1/2 conveyor configuration the extension of the input

conveyor could not be selected.

D1-129342401 The signal lamp status did not change.

D1-129406007 The board was not displayed as yellow board.

D1-129422634

D1-129758101

During production, the error message 32602 The software has

stopped unexpectedly. Shut down Windows, then restart the

station

occurred.

Station Software 710.0 (R16-2) / Version Description 12/2016 Edition

D1-129478801 Calibration of head / nozzle changer: the error message that wrong nozzles

are mounted came too soon. It should come after the head selection.

D1-129478898 There was an empty error message when a segment was deactivated during

the overall reference run of the machine.

D1-129506397

D1-129506341

Manual correction of deviation values only took effect on segment 1.

D1-129568901 eSW: Error occurred during offline verification flow.

D1-129683701 eSW: The gantry started to swing during mapping.

D1-129688301 eSW: The x/y axes swang up when the pickup or placement positions were

taught.

D1-129712103 It was not possible to go to the board fiducials (LBO board).

D1-129766401 If auto recovery was active, the error message 32539 Beware of

collision with high components

occurred.

D17710-10001 Vision: Sporadical placement shift caused by the placement position teaching

with gantry 2 and 4 in I-placement mode.

D18149-2501 The C&P20 P head reported 34441 The component sensor has

detected that a component is too thin after pickup

Table 8-4: Corrected errors station software 709.1 SP1

709.1 Hotfix 3

Error no. Error description

D1-125397801 The machine stopped during fiducial measuring.

D1-127315956 The The application has to be closed error message was displayed

on the GUI.

D1-127418201 eSW: Head verification: the z axis did not reach the required value.

D1-127731201 eSW: Sporadically, there were shifted components when they were placed

with low force.

D1-127741201 There was an error when the WPC6 was filled up.

D1-128083301 eSW: error message 31005 Cannot download data to the

subsystem

for all heads.

D1-128124943

D1-128090701

Error message: 30016 Unhandled exception error.

D1-128149593 The Component sensor coated error was triggered during endurance run

on gantry 2.

D1-128150232

D1-128088234

D1-128585501

D1-128140952

eSW: during dry run the machine stopped with the 40020 Unknown

placement state error message.

D1-128188101 The machine did not stop after an SWS error.

D1-128290801 2 nozzles could not be picked up from the nozzle changer after having

returned them manually.