00198235-01_VD_710.0_R16-2_DE_EN.pdf - 第31页

Station S oftware 71 0.0 (R16 - 2) / Version Descript ion 12/2016 Edition 31 D1 - 128580401 eSW : Error m essage 30450 Unspecified hardware error f or CPP head. D1 - 128590301 eSW : Subsystem was not activat ed and botto…

100%1 / 74
Station Software 710.0 (R16-2) / Version Description 12/2016 Edition
30
D1-129478801 Calibration of head / nozzle changer: the error message that wrong nozzles
are mounted came too soon. It should come after the head selection.
D1-129478898 There was an empty error message when a segment was deactivated during
the overall reference run of the machine.
D1-129506397
D1-129506341
Manual correction of deviation values only took effect on segment 1.
D1-129568901 eSW: Error occurred during offline verification flow.
D1-129683701 eSW: The gantry started to swing during mapping.
D1-129688301 eSW: The x/y axes swang up when the pickup or placement positions were
taught.
D1-129712103 It was not possible to go to the board fiducials (LBO board).
D1-129766401 If auto recovery was active, the error message 32539 Beware of
collision with high components
occurred.
D17710-10001 Vision: Sporadical placement shift caused by the placement position teaching
with gantry 2 and 4 in I-placement mode.
D18149-2501 The C&P20 P head reported 34441 The component sensor has
detected that a component is too thin after pickup
Table 8-4: Corrected errors station software 709.1 SP1
709.1 Hotfix 3
Error no. Error description
D1-125397801 The machine stopped during fiducial measuring.
D1-127315956 The The application has to be closed error message was displayed
on the GUI.
D1-127418201 eSW: Head verification: the z axis did not reach the required value.
D1-127731201 eSW: Sporadically, there were shifted components when they were placed
with low force.
D1-127741201 There was an error when the WPC6 was filled up.
D1-128083301 eSW: error message 31005 Cannot download data to the
subsystem
for all heads.
D1-128124943
D1-128090701
Error message: 30016 Unhandled exception error.
D1-128149593 The Component sensor coated error was triggered during endurance run
on gantry 2.
D1-128150232
D1-128088234
D1-128585501
D1-128140952
eSW: during dry run the machine stopped with the 40020 Unknown
placement state error message.
D1-128188101 The machine did not stop after an SWS error.
D1-128290801 2 nozzles could not be picked up from the nozzle changer after having
returned them manually.
Station Software 710.0 (R16-2) / Version Description 12/2016 Edition
31
D1-128580401 eSW: Error message 30450 Unspecified hardware error for CPP
head.
D1-128590301 eSW: Subsystem was not activated and bottom light barrier was not working.
D1-128638301 LC JobId (Order number) did not appear in Trace data.
D1-128674101 eSW: DPs could not be referenced.
D1-129330401 Error message 30455 The operating system of the processor
has a fatal error
(x axis).
D1-129418601 TX2 with CPP head: a dirty nozzle led to an endless nozzle scan.
Table 8-5: Corrected errors station software 709.1 Hotfix 3
709.1 Hotfix 1
Error no. Error description
D1-124980401
D1-125580001
D1-125592301
During placement, the 32608 StartStopClient_Gantry_1_R.HS:
Waiting until stopped error message appeared.
D1-127059901 When a PCB was removed manually from input side (when the PCB barcode
could not be read) while another PCB was transported to PA2, the machine
stopped without any error message.
D1-127115701 The label feeder was automatically removed from setup after a pickup error.
D1-127219609
D1-125810001
Sporadically, when the cover was open and help was selected, the software
hung up.
D17806-2401 Sporadically, there was a placement offset when the cover was opened.
D17987-3405 There was no error message when the 3D camera was disconnected from the
GCU.
Table 8-6: Corrected errors station software 709.1 Hotfix 1
Station Software 710.0 (R16-2) / Version Description 12/2016 Edition
32
9 Important Terms and Abbreviations
CA4 Machine type of the Chip Assembly (CA)-series with 4 gantries
and 2 PAs
C&P Collect & Place
CPP Collect & Place & Pick & Place
DC Dual Conveyor
DX1/DX2 Machine type with 1 or 2 gantries and 1 PA
EDIF Electronic Design Interchange Format
eWLP embedded Wafer Level Process
FCCS Field Camera Calibration System
GUI Graphical User Interface
HFH High Force Head
HW Hardware
MGCU Modular Gantry Control Unit
MHCU Modular Head Control Unit
MTC Matrix Tray Changer
OIS Operator Information System
PA Processing area
PCB Printed circuit board
Placement mode:
2-in-1
When a machine runs in I-Placement mode it is possible to
perform manual operations for one side / gantry.This placement
mode is also called "independent".
Placement mode:
Alternating
Placement mode in a dual gantry placement area, in which both
gantries place components on both boards in a dual conveyor.
First, both gantries place all assigned components on the board
in lane one and then on the board in lane two.
Placement mode:
Borrow
Performance
A line runs in I-Placement mode and to get a balanced
throughput between the left and right conveyor lanes, e.g. the
last machine runs in Alternating mode and places components in
this placement area on the board of the other lane.
Placement mode:
I-Placement
Placement mode in a dual gantry placement area in which each
gantry only places components on the board of the assigned
conveyor lane.
SC Single Conveyor
SC SIPLACE Setup Center (external setup control system)
SW Software
SWS SIPLACE Wafer System
SX1/SX2 Machine type with 1 or 2 gantries and 1 PA
TH Twin Head
TH HF Twin Head High Force
Twin VHF Very High Force Twin Head