252301 Issue 2.0.pdf - 第105页

GEM Manual for DEK Printers Equipment Va riables I ssue 2.0 June 9th, 2011 page 105 of 156 7.2 Equipment Constants The equipment constants are defined in the table be l ow: Note: Default values a re shown bold . NAME ECI…

GEM Manual for DEK Printers Equipment Variables

Issue 2.0 June 9th, 2011 page 104 of 156

7.1 Introduction

A set of variable definitions is provided to enable the host to monitor and sometimes alter, the

behaviour of the equipment. These are known as machine variables.

Machine variables are divided into the following three categories.

Equipment Constants: Allow the host to modify certain aspects of the equipment’s

behaviour. See section 5.5 for a discussion on the use of EC’s.

Status Variables: As the name suggests, these variables track continuous system

status values. The host can interrogate the equipment at any time

and can programme the equipment to transmit values on a

regular schedule. The host can not change these values.

See section 5.2 for a discussion on data collection methods.

Discrete Data Variables: Are similar to Status Variables except that their values are valid

only when specific events occur. The host should not interrogate

these values, but should include them in reports linked to

collection events.

See section 5.2 for a discussion in on data collection methods.

Process Attributes: These variables are used to request name and value information

about the currently loaded printer product.

The machine variables are listed by category in the following sections.

GEM Manual for DEK Printers Equipment Variables

Issue 2.0 June 9th, 2011 page 105 of 156

7.2 Equipment Constants

The equipment constants are defined in the table below:

Note: Default values are shown bold.

NAME ECID DESCRIPTION Type Value Range

GemConfigConnect 1 Select establish communications type. U1

1 = S1F13

DeviceName 2 Equipment name as defined by the host. A20 20 characters

GemEstabCommDelay 3 Time between each S1F13 poll. U2

0-60-1800 s

GemPollDelay 4 Time between each S1F1 poll. U2

0-60-1800 s

GemInitCommState 5 Initial communications state. U1 1 = Enable

0 = Disable

GemInitControlState 6 Initial control state. U1

1 = OFF-LINE

2 = ON-LINE

GemOfflineSubstate 7 Set default control sub-state when equipment is

OFF-LINE.

1 = Equipment Off-Line

2 = Attempt On-Line

3 = Host Off-Line

GemOnlineFailed 8 Default sub-state following ON-LINE failure. U1

1 = Equipment Off-Line

2 = Host Off-Line

GemOnlineSubstate 9 Default sub-state when entering ON-LINE state. U1

4 = Local

5 = Remote

received_mode 10 Set System Mode. This constant is volatile and

defaults to Auto on machine power up.

1 = Auto

2 = Single

3 = Pass Through

InspectRate 11 Number of print cycles between board

inspections. 0 indicates no inspection

0 – 100

BatchLimit 12 Number of boards to be printed in a production

batch. O indicates no batch limit

0 - 99999

process_adjustments 13 Enables/disables adjustment of the current

printing process while the machine is running.

0 = Enabled

1 = Operator disabled

2 = Remote command

disabled

3 = Both disabled

MaxSpoolTransmit 14 The maximum number of messages that the

equipment will transmit from the spool in

response to a S6F23”Transmit spooled

Messages” request. If MaxSpoolTransmit is set

to zero, no limit is placed on the messages sent

from the spool. Multi-block inquire/grant

messages are not counted in this total.

Minimum = 0

Maximum = value of

SpoolCountActual

OverWriteSpool 15 Tells the printer to overwrite data in the spool

area or stop spooling whenever the spool area

limits are exceeded.

1 = TRUE to overwrite

spooled data

0 = FALSE to stop

spooling when limits are

exceeded.

spooling_enabled 16 Allows the equipment to default to a condition

where spooling is disabled completely. This is

provided for older Hosts that do not support

S6F23. This EC is set to TRUE = 1 on receipt of

S2F43 defining messages to be spooled.

0 = FALSE spooling

disabled

If the Host sets this EC to

FALSE any data in the

spool will be purged.

Reserved 17-39 Not used by the 265.

TimeFormat 40 The setting of this ECV controls whether the

equipment shall send the Data Items STIME and

TIME in 12-byte or 16-byte format. It also

controls the format of START_TIME. to be 6 or

7 bytes.

B1 0 = 12 byte format

1 = 16 byte format

>1 reserved

GEM Manual for DEK Printers Equipment Variables

Issue 2.0 June 9th, 2011 page 106 of 156

NAME ECID DESCRIPTION Type Value Range

RunGEMRemote 41 Allows control of the Run With GEM Remote

parameter. When enabled, only the host can

start the printer and the operator is given an

appropriate message.

0 = Disable

1 = Enable

Start Modification >>>

MaterialVerif 42 Used to specify whether the material verification

feature is enabled or disabled

0 = Disabled

1 = Enabled

MaterialVerifState 43 Used to drive the material verification state

machine. This is a model shared between the

host and the Printer. It is used to synchronise

verification activity

0 = Disabled

1 = Unread

2 = Reading Tag

3 = Verification Pending

4 = Invalid

5 = Valid

6 = Overridden

7 = Verification Complete

8 = Error

SCValidatedMaterial 44 Used to store the UID of the material last

validated by the host. The host should set this

value prior to attempting to set the material

verification state

A64 Up to 64 character string

RCPOWCode 45 Controls if local products will be overwritten if

a product with the same name is uploaded

B1 0 = False (overwrites are

rejected)

1 = True (overwrites are

allowed)

CompoundProductFiles 46 Controls if the individual files for a process

program will be combined into a single data

transfer.

B1 0 = False (only the PR1

file will be transferred)

1 = True (all files will be

transferred in one block)

Make 50 Printer make. Always returns “DEK” (read-

only)

A20

“DEK”

Model 51 The model of the printer (read-only) A20 For example “Galaxy”

StencilCleaningSystem 53 The currently selected cleaner module (read-

only)

0 = None

1 = Blue

2 = Vortex

3 = Cyclone

ApplicatorType 54 The currently selected applicator module (read-

only)

0 = Squeegees

1 = ProFlow (classic)

2 = Ball Placement

3 = ProFlow Tx

4 = ProFlow ATx

ConveyorType 55 The fitted conveyor type (read-only) U1

0 = Standard

1 = HTC

2 = RTC

TransportMode 56 The current rail transport mode U1

0=LeftToRight

1=RightToLeft

2=RightToRight

3=LeftToLeft

4=NoTransfer/Shuttle

MachineUnits 57 The current machine units U1

0=Metric

1=Imperial

UplineProtocol 58 The current up-line FMI protocol U1 0=NoFMI

1=MIU

2=Manual

DownlineProtocol 59 The current downline FMI protocol U1 0=NoFMI

1=MIU

2=Manual

TransferPeriod 60 FMI transfer period (s) U2

0 – 999, 20