252301 Issue 2.0.pdf - 第129页
GEM Manual for DEK Printers Event Messag es I ssue 2.0 June 9th, 2011 page 129 of 156 EVENT - CEID DESCRIPTION 31315 Head moved to safe state. 9.7 Spooling Events EVENT - CEID DESCRIPTION 31453 Spooling activated. 31454 …
GEM Manual for DEK Printers Event Messages
Issue 2.0 June 9th, 2011 page 128 of 156
9.1 Control Model Events
EVENT - CEID
DESCRIPTION
31450 Control State – Change to LOCAL.
31451 Control State – Change to OFF-LINE.
31452 Control State – Change to REMOTE.
31456 Operator command issued.
9.2 Process Model Events
EVENT - CEID
DESCRIPTION
90001 Equipment moved to Recovery state.
90002 Equipment moved to Setup state.
90003 Equipment moved to Ready state.
90004 Equipment moved to Maintenance state.
90005 Equipment moved to Waiting state.
90006 Equipment moved to Running state.
90007 Equipment moved to Down state.
9.3 Process Program Management Events
EVENT - CEID
DESCRIPTION
31265 Process program loaded.
31266 New process program created and loaded.
31267 Process program change.
31346 Product Data modified (with change details – see section 9.15)
Start Modification >>>
32035 Operator deleted process program
<<< End Modification
9.4 Equipment Constant Change Event
EVENT - CEID
DESCRIPTION
31440 Equipment constant change.
9.5 Acknowledge Terminal Message Event
EVENT - CEID
DESCRIPTION
31441 Acknowledge terminal message.
9.6 Alarm Events
EVENT - CEID
DESCRIPTION
31253 Cover opened.
31254 Cover closed.
31314 Head left partly open.
GEM Manual for DEK Printers Event Messages
Issue 2.0 June 9th, 2011 page 129 of 156
EVENT - CEID
DESCRIPTION
31315 Head moved to safe state.
9.7 Spooling Events
EVENT - CEID
DESCRIPTION
31453 Spooling activated.
31454 Spooling deactivated.
31455 Spool transmission failure.
9.8 Equipment Error Events
EVENT - CEID
DESCRIPTION
10003 System power down.
31201 Pneumatic power down.
31202 Front squeegee error.
31203 Rear squeegee error.
31204 Rising table error.
31205 Print carriage error.
31206 Paste carriage error.
31207 Camera X axis error.
31208 Camera Y axis error.
31209 Rail width error.
31210 Screen XF error.
31211 Screen XR error.
31212 Screen Y error.
31213 Paste cartridge tilt error.
31214 Screen changer drive error.
31215 Board stop stuck.
31216 Board clamp stuck.
31217 Board stuck in rails.
31218 Unable to find fiducial.
31219 Rail lifted error.
31220 Print pressure error.
31221 File error.
31222 Unable to recover.
31223 Recovery started.
31224 Recovered.
31225 Upline transfer error.
31226 Downline transfer error.
31227 Dual shuttle fault.
31230 Screen changer fault.
31232 Lid bolt fault.
31233 Alignment out of range.
31417 Comms error.
31303 Barcode read failure.
31304 Barcode mismatch.
31305 Screen couplings failed.
GEM Manual for DEK Printers Event Messages
Issue 2.0 June 9th, 2011 page 130 of 156
EVENT - CEID
DESCRIPTION
31306 Motion control timeout.
31307 Camera X failed to position.
31308 Camera Y failed to position.
31309 Stencil aperture blocked.
31310 Stencil smeared.
31311 Paste on pad inspection error.
31312 Bridging detected by inspection system.
31313 Alignment error detected by inspection system.
31321 Event log disk file full.
31322 Proflow error.
31340 CAN node down.
31341 CAN node recovered.
31342 CAN bus down.
31433 CAN bus recovered.
31460 Volume alarm.
40006 Dongle error.
40028 Roll Height Monitor failed
40043 Knead pressure error (front)
40044 Knead pressure error (rear)
40045 Print pressure error (front)
40046 Print pressure error (rear)
40047 Servo following error
40048 Board fiducial 1 not found
40049 Board fiducial 2 not found
40050 Board fiducial 3 not found
40051 Screen fiducial 1 not found
40052 Screen fiducial 2 not found
40053 Screen fiducial 3 not found
40054 Select mark not found
40056 Bad tooling vacuum
40146 Cleaner detached from camera
40147 Recovered cleaner detached from camera
40150 Ball escape detected
40152 Verification item failed (see DVID 2034)
40157 Product ID verification failed
Start Modification >>>
40200 Material RFID Tag Read Failed
40208 RFID Node Error
40320 Cleaner Vacuum Sense Error
<<< End Modification
9.9 Equipment Specific Information Events
EVENT - CEID
DESCRIPTION
10002 System power on.
31251 Line power on.
31252 Line power off.