252301 Issue 2.0.pdf - 第130页
GEM Manual for DEK Printers Event Messag es I ssue 2.0 June 9th, 2011 page 130 of 156 EVENT - CEID DESCRIPTION 31306 Motion control timeout. 31307 Camera X failed to position. 31308 Camera Y failed to position. 31309 Ste…
GEM Manual for DEK Printers Event Messages
Issue 2.0 June 9th, 2011 page 129 of 156
EVENT - CEID
DESCRIPTION
31315 Head moved to safe state.
9.7 Spooling Events
EVENT - CEID
DESCRIPTION
31453 Spooling activated.
31454 Spooling deactivated.
31455 Spool transmission failure.
9.8 Equipment Error Events
EVENT - CEID
DESCRIPTION
10003 System power down.
31201 Pneumatic power down.
31202 Front squeegee error.
31203 Rear squeegee error.
31204 Rising table error.
31205 Print carriage error.
31206 Paste carriage error.
31207 Camera X axis error.
31208 Camera Y axis error.
31209 Rail width error.
31210 Screen XF error.
31211 Screen XR error.
31212 Screen Y error.
31213 Paste cartridge tilt error.
31214 Screen changer drive error.
31215 Board stop stuck.
31216 Board clamp stuck.
31217 Board stuck in rails.
31218 Unable to find fiducial.
31219 Rail lifted error.
31220 Print pressure error.
31221 File error.
31222 Unable to recover.
31223 Recovery started.
31224 Recovered.
31225 Upline transfer error.
31226 Downline transfer error.
31227 Dual shuttle fault.
31230 Screen changer fault.
31232 Lid bolt fault.
31233 Alignment out of range.
31417 Comms error.
31303 Barcode read failure.
31304 Barcode mismatch.
31305 Screen couplings failed.
GEM Manual for DEK Printers Event Messages
Issue 2.0 June 9th, 2011 page 130 of 156
EVENT - CEID
DESCRIPTION
31306 Motion control timeout.
31307 Camera X failed to position.
31308 Camera Y failed to position.
31309 Stencil aperture blocked.
31310 Stencil smeared.
31311 Paste on pad inspection error.
31312 Bridging detected by inspection system.
31313 Alignment error detected by inspection system.
31321 Event log disk file full.
31322 Proflow error.
31340 CAN node down.
31341 CAN node recovered.
31342 CAN bus down.
31433 CAN bus recovered.
31460 Volume alarm.
40006 Dongle error.
40028 Roll Height Monitor failed
40043 Knead pressure error (front)
40044 Knead pressure error (rear)
40045 Print pressure error (front)
40046 Print pressure error (rear)
40047 Servo following error
40048 Board fiducial 1 not found
40049 Board fiducial 2 not found
40050 Board fiducial 3 not found
40051 Screen fiducial 1 not found
40052 Screen fiducial 2 not found
40053 Screen fiducial 3 not found
40054 Select mark not found
40056 Bad tooling vacuum
40146 Cleaner detached from camera
40147 Recovered cleaner detached from camera
40150 Ball escape detected
40152 Verification item failed (see DVID 2034)
40157 Product ID verification failed
Start Modification >>>
40200 Material RFID Tag Read Failed
40208 RFID Node Error
40320 Cleaner Vacuum Sense Error
<<< End Modification
9.9 Equipment Specific Information Events
EVENT - CEID
DESCRIPTION
10002 System power on.
31251 Line power on.
31252 Line power off.
GEM Manual for DEK Printers Event Messages
Issue 2.0 June 9th, 2011 page 131 of 156
EVENT - CEID
DESCRIPTION
31255 Printer ready.
31256 Head raised.
31257 Head closed.
31260 Cycle aborted.
31261 Cycle completed.
31262 Cleaning screen.
31263 Parameter adjusted. (See Appendix A)
31264 Setup started.
31272 Setup ended.
31273 Start print cycle.
31275 End print cycle.
31277 Board printed.
31278 Operator log on.
31279 Operator log off.
31280 Clear batch count.
31281 Start maintenance.
31282 End maintenance.
31283 Pressure recalibrated.
31284 Offset recalibrated.
31285 X,Y scale recalibrated.
31286 Theta recalibrated.
31287 Configuration change.
31288 Start diagnostics.
31289 End diagnostics.
31291 Camera reference reset.
31293 Vision height reset.
31294 Print height reset.
31296 Software updated.
31297 New event log.
31301 No cleaner paper.
31302 No cleaner solvent.
31316 Inspection cycle complete.
31317 Clock change request.
31318 Clock changed.
31330 User has enabled the Autoflex tooling.
31331 User has disabled the Autoflex tooling.
31332 System has enabled Autoflex tooling.
31333 System has disabled Autoflex tooling.
31334 Tooling data changed.
31345 Configuration Parameter modified (with change details – see section 9.15)
31347 Adjust Parameter modified (with change details – see section 9.15)
31457 Remote barcode received.
31459 options.enb file attribute error.
40004 Evaluation dongle detected.
40005 Valid dongle detected.
40007 Dongle changed.
40008 Front print speed.