00197787-02_SI_SIPLACE_HeadVerification_EN.pdf - 第31页
5 Online head verification workflow 5.3 Available measurements for C&P20P Software Manual SIPLACE Head Verification 03/2018 31 5.3 Available measurements for C&P20P Required tools ● 1x calibration jig version S…
5 Online head verification workflow
5.2 Available measurements for C&P20A
30 Software Manual SIPLACE Head Verification 03/2018
5.2 Available measurements for C&P20A
Required tools
●
1x calibration jig version SST23 [03034148-xx]
●
20x Nozzle 1235 [03015222-xx]
●
20x Nozzle 1069 [03094112-xx]
Verification workflow
NOTICE
Head Verification versus Test Bench Inspection mode
The Head Verification mode provides a fast verification with the main focus on the Z-axis
and the vacuum system. All red framed tasks are not shown.
The Test Bench Inspection mode includes all available tasks as shown in figure "Available
measurements for C&P20A (Test Bench Inspection mode)" [}30].
Fig.28: Available measurements for C&P20A (Test Bench Inspection mode)
1 Filter disc
See 6.10 "Filter Disc" [}52]
2 CS Sensor voltage and z-heights
See 6.5 "CS Sensor voltage and z-heights" [}44]
3 Holding circuit (sealed nozzles)
See 6.17 "Holding circuit (sealed nozzles)" [}68]
4 Anti-glare shield mounting
See 6.4 "Anti-glare shield mounting" [}42]
5 Nozzle spring
See 6.18 "Nozzle spring" [}70]
6 Z-axis movement
See 6.22 "Z-axis movement" [}81]
7 Air & vacuum with head sensors
See 6.2 "Air & vacuum with head sensor" [}37]
8 Segment offset up & down (fast)
See 6.19 "Segment offset up & down (fast)" [}72]
9 Head Endurance Run 01005
See 6.14 "Head endurance run 01005" [}60]
10 Head Endurance Run LS
See 6.16 "Head endurance run LS" [}65]
5 Online head verification workflow
5.3 Available measurements for C&P20P
Software Manual SIPLACE Head Verification 03/2018 31
5.3 Available measurements for C&P20P
Required tools
●
1x calibration jig version SST23 [03034148-xx]
●
20x nozzle 4004 [03098544-xx]
●
20x nozzle 4235 [03015222-xx]
●
20x nozzle 4105 [03102457-xx]
●
20x nozzle 4069 [03106244-xx]
Verification workflow
NOTICE
Head Verification versus Test Bench Inspection mode
The Head Verification mode provides a fast verification with the main focus on the Z-axis
and the vacuum system. All red framed tasks are not shown.
The Test Bench Inspection mode includes all available tasks as shown in figure "Available
measurements for C&P20P (Test Bench Inspection mode)" [}31].
Fig.29: Available measurements for C&P20P (Test Bench Inspection mode)
1 ZDS sensor values
See 6.24 "ZDS sensor values" [}84]
2 DP rotation test
See 6.8 "DP rotation test" [}48]
3 Segment offset up & down (fast)
See 6.19 "Segment offset up & down (fast)" [}72]
4 Nozzle spring
See 6.18 "Nozzle spring" [}70]
5 Holding circuit (sealed nozzles)
See 6.17 "Holding circuit (sealed nozzles)" [}68]
6 CS Sensor voltage and z-heights
See 6.5 "CS Sensor voltage and z-heights" [}44]
7 Z axis movement
See 6.22 "Z-axis movement" [}81]
8 Air & vacuum with head sensors
See 6.2 "Air & vacuum with head sensor" [}37]
9 Head Endurance Run LS
See 6.16 "Head endurance run LS" [}65]
5 Online head verification workflow
5.4 Available measurements for CPP
32 Software Manual SIPLACE Head Verification 03/2018
5.4 Available measurements for CPP
Required tools
●
1x calibration part version 3 [03010565-xx]
●
12x nozzle 2069 [03094135-xx]
●
12x nozzle 2057 [03070280-xx]
●
12x magazine for 2xxx nozzle [03066107-xx]
Verification workflow
NOTICE
Head Verification versus Test Bench Inspection mode
The Head Verification mode provides a fast verification with the main focus on the Z-axis
and the vacuum system. All red framed tasks are not shown.
The Test Bench Inspection mode includes all available tasks as shown in figure "Available
measurements for CPP (Test Bench Inspection mode)" [}32].
Fig.30: Available measurements for CPP (Test Bench Inspection mode)
1 CS-Sensor voltage and z-heights
See 6.5 "CS Sensor voltage and z-heights" [}44]
2 Dp- / Z-Positioning
See 6.9 "Dp- / Z-Positioning" [}50]
3 Holding circuit (sealed nozzles)
See 6.17 "Holding circuit (sealed nozzles)" [}68]
4 Nozzle spring
See 6.18 "Nozzle spring" [}70]
5 Z-axis movement
See 6.22 "Z-axis movement" [}81]
6 Air & vacuum with head sensors
See 6.2 "Air & vacuum with head sensor" [}37]
7 DP rotation test
See 6.8 "DP rotation test" [}48]
8 Segment offset up & down (fast)
See 6.19 "Segment offset up & down (fast)" [}72]
9 Head Endurance Run 01005
See 6.14 "Head endurance run 01005" [}60]
10 Head Endurance Run LS
See 6.16 "Head endurance run LS" [}65]