FlexSeam Dispensing System Customer Product Manual.pdf - 第58页
Flexseam Dispensing System 54 Part 1127900_01 E 2019 Nordson Corporation Technical Data Flexseam Dispensing System Specifications Component Item Specification System Transport temperature ‐45-75 _ C (‐49-167 _ F) Storage…
Flexseam Dispensing System
52
Part 1127900_01
E 2019 Nordson Corporation
Lip Part Numbers
See Figure 26.
Part Description
7402556 L LIP COVER,7-10MM,FS
7403295 LIP,SLOT,ROBOT,0.3X0.6MM,8MM,4DOTS
7403299 LIP,SLOT,ROBOT,0.3X0.6MM,10MM,5DOTS
7404508 LIP,SLOT,ROBOT,0.2X0.35MM,7MM,4DOTS
7404509 LIP,SLOT,ROBOT,0.3X0.3MM,9MM,5DOTS
7404622 L LIP COVER,7-10MM,I,FS
1
2
Figure 26 Lip parts
1. Nozzle lip 2. Shave lip (with mark)
Flexseam Dispensing System
53
Part 1127900_01
E 2019 Nordson Corporation
Recommended Spare Parts and Supplies
Equipment Part Item Note
System 1094186 DRYER,AIR,DESICCANT,INLINE,1/4NPT
Flexseam Applicator
7407694 KIT-SVC,SOLENOID VALVE,HIGH FREQUENCY,FS
7407697 KIT-SVC,NOZZLE PLATE 7-10MM,FS A
7407698 KIT-SVC,HARNESS,NOZZLE HEATER&RTD
7407699 KIT-SVC,HARNESS,CARTRIDGE HEATER&RTD
7407700 KIT-SVC,NEEDLE,FLAT,FS
7407701 KIT-SVC,O-RING,MODULE PUMP,FS
7407702 KIT-SVC,O-RING,NEEDLE,10/PACK,FS
7407703 KIT-SVC,AIR CAP,1.5MM
7407704 KIT-SVC,O-RING,AIR CAP,10/PACK
7407705 KIT-SVC,O-RING,NOZZLE PLATE
7407706 KIT-SVC,CAP,300CC
7404199 KIT-SVC,INSULATION, CARTRIDGE
7404200 KIT-SVC,O-RING, MODULE PLATE
7402541 CORDSET,SOL,PJ,UNITY TOUCH
7403228 CABLE,M8 MALE 0,FEMALE 90
7404246 KIT-SVC,PLATE,SEPA,JP1,DUAL DOTS
7404247 KIT-SVC,NOZZLE,SEPA,DUAL,JDN1
7404248 KIT-SVC,O-RING,NOZZLE,JP1,FS
7404244 KIT-SVC,AIR CAP,2.0MM
7404249 KIT-SVC,NEEDLE,RN1,FS
NOTE A: Apply to 7-10mm dispensed adhesive width for smooth fabric.
Flexseam Dispensing System
54
Part 1127900_01
E 2019 Nordson Corporation
Technical Data
Flexseam Dispensing System Specifications
Component Item Specification
System
Transport temperature ‐45-75 _C (‐49-167 _F)
Storage temperature ‐45-75 _C (‐49-167 _F)
Ambient temperature 0-40 _C (32-104 _F)
Humidity 10-95% non‐condensing
Flexseam applicators
Weight Flexseam applicator: 7kg (15.4 lb)
Material compatibility Rated for use with all commercially available
pressure sensitive and EVA hot melt
adhesives and polyurethane reactive (PUR)
adhesives, excluding any compound that
contains polyamides
Adhesive viscosity Varies depending on nozzle size and flow rate
Operating temperature 40° to 160/230° C (104° to 320/446° F)(160°
C/320° F only for Zone1)
Working hydraulic pressure 2 to 6 bar (29 to 87psi)
Maximum hydraulic pressure 6 bar (87 psi)
Maximum applicator running
speed
200 mm/s
Actuation air pressure 5 bar (72.5 psi) recommended
Temperature control stability ±1°C (2°F)
Temperature control sensor Ni120
Electrical service 230 VAC 1 phase 50/60 Hz
Installation dimensions (W x H x D) 1420 x 632 x 1791 mm (55.9 x
24.9 x 70.5 in.)