5OM-1064-001.pdf - 第15页

3.1 Picture Adjustment When [Picture Adjustment] is selected at the “Screen Manager” dialog box and “Center” of the operation pad is pressed, the menus for picture adjustment appear in the dialog box. Select the item to …

100%1 / 190
Color Adjustment
࡮Standard Mode (Selection of Color Temperature)
࡮Custom Mode (Creation of Color Tones)
Picture (Screen) Adjustment
࡮Contrast/Brightness ࡮Size
࡮Position ࡮Parallelogram
࡮Pincushion ࡮Tilt
࡮Moire
Information
The present settings can be checked.
The information is divided into four pages which can be opened by
pressing "Center" of the operation pad. Each page is numbered as 1/4,
2/4, 3/4 and 4/4.
Each page contains the information as follows.
1/4: Vertical/Horizontal Frequency and Moire Effect Correction
2/4: Color Mode and Temperature
3/4: Setting of Power Manager
4/4: Bee
p
Others
࡮Degaussing ࡮ Beep
࡮Menu Position ࡮ Menu Contrast
࡮Reset
Language Selection
Japanese or English can be selected for expressions in "Screen
Manager".
Power Manager (Setting of Power-Save Mode)
3. Settings
• Use “Screen Manager” to adjust the recognition monitor.
• Menus of Screen Manager
CAUTION
Do not change the following settings unless
necessary. The monitor is factory-adjusted
upon shipment.
• Custom Mode of “Color Adjustment”
• Power Manager (Power-Save Mode: OFF)
• Language Selection
• Others
If the above settings are not made correctly,
the monitor may not work normally.
Ref.: Before performing any adjustment, keep the monitor intact for more
than 30 minutes after the power is supplied.
It takes approximately 30 minutes before the cathode-ray tube gets
warm enough, the internal electrical components are stabilized and the
colors develop in stable condition.
Fig. 1.3
3. Settings
0005-002 1-4 Tg0250-PM-MD
3.1 Picture Adjustment
When [Picture Adjustment] is selected at the “Screen Manager” dialog box
and “Center” of the operation pad is pressed, the menus for picture adjustment
appear in the dialog box.
Select the item to be adjusted and press “Center” of the operation pad.
Contrast/Brightness
• The contrast (difference in intensity) and brightness of the reproduced
picture can be adjusted.
Fig. 1.4
Ref.:
Adjustment Procedure for Average Brightness
Fig. 1.5
(1) Select “Contrast/Brightness” for maximum brightness.
(2) Select “Size” at “Picture Adjustment” of the “Screen Manager” dia-
log box.
When the screen size is reduced to the minimum, a glimmer frame
(raster) appears outside the reproduced picture.
(3) Select “Contrast/Brightness”.
Decrease the brightness until the raster has the same brightness as
the available picture area (until the raster disappears).
The brightest picture will be reproduced with great contrast.
(4) Resume the original size and adjust the contrast to the desired one.
The brightness
increases.
The brightness
decreases.
The contrast
increases.
The contrast
decreases.
"Contrast
and Brightness"
Press this to
the bottom.
Press this to
the top.
Press this to
the right.
Press this to
the left.
3. Settings
0005-002 1-5 Tg0250-PM-MD
Raster
Reproduced Picture
Available Picture Area
Size
• The screen size can be adjusted.
Fig. 1.6
Position
• The raster on the display screen can be positioned.
Fig. 1.7
Distortions (Barrel/Pincushion and Trapezoid/Parallelogram)
• Distortions of the raster can be adjusted.
Two kinds (barrel/pincushion and trapezoid/parallelogram) of distor-
tions can be adjusted.
Fig. 1.8
Barrel/Pincushion
"Pincushion"
The pincushion
distortion can be
adjusted.
The pincushion
distortion can be
adjusted.
The barrel
distortion can
be adjusted.
The barrel
distortion can
be adjusted.
Press this to
the bottom.
Press this to
the top.
Press this to
the right.
Press this to
the left.
"Size"
The raster on the
display screen
becomes wider for
the correct
proportions of
width to height.
The raster on the
display screen
becomes narrower
for the correct
proportions of
width to height.
The raster on the
display screen
becomes shorter for
the correct
proportions of
height to width.
The raster on the
display screen
becomes taller for
the correct
proportions of
height to width.
Press this to
the bottom.
Press this to
the top.
Press this to
the right.
Press this to
the left.
"Position"
The raster on the
display screen
moves to the right.
The raster on the
display screen
moves to the left.
The raster on the
display screen
moves to the
bottom.
The raster on the
display screen
moves to the top.
Press this to
the bottom.
Press this to
the top.
Press this to
the right.
Press this to
the left.
3. Settings
0005-002 1-6 Tg0250-PM-MD