JUKI KE775点胶机说明书1.pdf - 第36页
CHAPTER2DEsCRIPTION OF THE0PERATOR CONTR0Ls ■ others Funcuons ofthe keys otherthan those a丨 ready desc"bed are shown asfo"ovvs. Table?ˉ 1ˉ 7Functions of keys(others) CAUTION When the H0D unitis connected to the…
CHAPTER2DEsCRIPTI0N0F THE OPERAT0R CONTR0Ls
■
TEACH IN group
TEAC卜
丬IN group Iights up LEDs and dispIays the currentteaching data as shown in the tabIe beloW.
TabIe2ˉ
1ˉ 5廴ED dispIay
No
H0D display
Data under∶ teaching
1
XY
XY Coordinates
2 θ
Angle
3
VIsl0N
Recogn"ion parameter
■
CONVEY0R group
Keys ofthe AWC group are used are used when perfornη
ing adjustment of PVVB VVidth and to enterthe fine
a呐
ustment value ofthe board width when the op刂
onaI automatic board width a哟
ustment device is mounted.
Function of each keyis as shown in the tab丨
e beIOw
TabIe2艹
6FunCⅡ
ons of keys(CONVEYOR group)
No
Key
FunCtion
1
至
Rotates the motor for board width adjustmentin the direction o亻
widening the board Width
2
ROtates the motorfor board Width adjustment in the direction of
narrowing the board Width
3
lN/0UT米
se丨 ects or releases the rnotor for lnput/0utput buffer
LED lights up
Ⅵ
`h"e being selected
丨tis possib丨
e to simu"aneousIy se丨
ect the motor for center station
4
CENTER seleCts or re丨
eases the rnotor forthe center station
LED lights up Wh"e being se丨
ected
"is possible to sirnu"aneously se丨
eCt the motor for lnpuv。
utput
buffer
FAsT
Changes overthe moving speed at high/low speed
LED Iights uρ
in the high speed mode
米
:t is effeCtive onIy l″
hen opt:naI automatic PWB width adjustmentfunCt∶
on:s proˇ
ided.
2ˉ 6
CHAPTER2DEsCRIPTION OF THE0PERATOR CONTR0Ls
■
others
Funcuons ofthe keys otherthan those a丨 ready desc"bed are shown asfo"ovvs.
Table?ˉ 1ˉ
7Functions of keys(others)
CAUTION
When the H0D unitis connected to the mach∶
ne proper,do it onIy after turning off p°
wer supply to the
equ:pment proper。
CAuTION
Magnet shρ
et(magnet)is pasted on the rear side ofthe HoE冫
unit.:f FIoppy Disk° rthe like is pIaced near to
the unit,there is a dangerthatthe data stored on the disk may be erased,
No
Key Func】 on
1
、
ⅣlND0W changes overthe Cross rnark cursorto the box type curs°
r,
LED lights up wh"e the box type cursoris being displayed
2
CANCEL lnVa"dates data and the teaChing rnode is released
ENTER Va"dates data and the teaching rη
ode returns to the prevIous rnode
4
PAUsE Performs temporary stop and its release
Ⅵ
`hen traCking the dispensing by automatic feed
LED lights up whⅡ
e temporari丨
y stopped
5
PREVI0∪ s MOVes to the preVious dispensihg point when tracking the dispensing
6
N EXt MOves to the neXt d丨 spens∶
ng point Ⅵ
`hen track:ng the dispencing
7
BL0W TlMER Adds pressure on the head selected by DEVIcE as much as the setting timer VaIue
Pressing the key again whⅡ
e adding pressure interrupts this function eVen vvhen the tirneris
on the way
To c|early separate the second pressure addlng from the interruption operation when the
key is pressed immediately after compleuon。
f adding pressure by the tirner,there is
approxirnately one second of non-fee"ng ti丨
ηe a竹
erthe end ofthe tirner
BL0W MANUAL
Adds pressure on the head seleCted by DEVlCE as Iong as itis being pressed
2ˉ 7
CHAPTER2DEsCRIPTION OF THE oPERATOR C0NTROLs
2ˉ 1ˉ3.PoWer unit(No fuse breaker)
The power swⅡ ch ofthe rnachine is found nearthe bottom on the le仪
side panel as shown in Fig 2ˉ3,Pu"the
lever upvvard to turn ON the rnachine and the power丨
amp Iights up
This s、
VitCh seⅣes aIso as a circuit breaker,ShouId an overcurrentfIoWs through the rnachine,it automatica"y
shuts down the power
—
cAuTION
Never operate the equipment based on differentˇ
oItage specif:cations。
Fig,2△
ˉ
g POWersW∶
tch
2ˉ 8