ITT-Cannon-RF50-Catalog.pdf - 第51页

Cannon 50 Ohm Connectors ASSEMBL Y INSTRUCTIONS 51 A A I I - - 7 7 0 0 3 3 S S M M A A S S t t r r a a i i g g h h t t C C o o n n n n e e c c t t o o r r s s , , C C a a p p t t i i v v e e C C o o n n t t a a c c t t ,…

100%1 / 64
Cannon 50 Ohm Connectors ASSEMBLY INSTRUCTIONS
50
www
.ittcannon.com
BBAAII--000033 SSMMBB // SSMMCC SSttrraaiigghhtt CCoonnnneeccttoorrss,, CCrriimmpp TTyyppee ffoorr BBrraaiiddeedd CCaabbllee
CRIMP FERRULE REAR BODY REAR INSULATOR CONTACT FRONT
INSULATOR
FRONT
BODY
`
A
B
C
1. Slide ferrule on cable.
2. Trim cable to dimensions shown taking care not to nick braid or center
conductor.
3. Tin center conductor (DO NOT OVER TIN).
4. Slide rear body over cable dielectric and under the braid until the braid is
flush against the rear of the hexagonal nut. NOTE: When using cables with
inflexible jackets two 3,17 (.125) slits in the outer jacket are permissible.
5. Slide on rear insulator so that the counterbore rests against the cable
dielectric.
6. Place a small solder preform made from 0,26 - 0,31 (.010 - .012) dia (28
swg) multi-core solder in rear of contact.
7. Assemble contact on center conductor, heat to make solder connection
ensuring shoulder of contact is flush against rear insulator. NOTE: Do not
allow solder to protrude outside spill hole.
8. Slide ferrule against body and crimp using Cannon’s Crimp Tool and suitable
Die Set (see table below).
9.
Slide on front insulator (if not already assembled in body).
10.
Screw on front body and tighten to 0,63 - 0,70 Nm (90 - 100 in. ozs.)
Only common cable retention features are shown in detail. Various body
configurations can apply
.
Assembly Instruction No.
BAI-003
A
15,50 (.610)
B
9,50 (.374)
C
2,50 (.098)
Cable Numbers
RG142/U
RG196/U
RG316/U
RD316
Cable Code
9052
3196
0000
9399
Die Size
5,41 (.213)
2,67 (.105)
3,25 (.128)
3,84 (.151)
Die Set
K29265
K29263
K29263
T1025/9
STEP 5
STEP 4
STEP 2
STEP 1
STEP
10
STEP 8
STEP 7
Cannon 50 Ohm Connectors ASSEMBLY INSTRUCTIONS
51
AAII--770033 SSMMAA SSttrraaiigghhtt CCoonnnneeccttoorrss,, CCaappttiivvee CCoonnttaacctt,, CCrriimmpp TTyyppee
ffoorr BBrraaiiddeedd CCaabbllee
HEAT SHRINKABLE
TUBING
CRIMP
FERRULE
RETAINING
NUT
REAR BODY CENTER
CONTACT
FRONT BODY
B
C
A
1. Strip cable to dimensions shown. Do not nick outer or inner conductors.
Tin inner conductor.
2. Place shrink tubing, crimp ferrule and retaining nut on cable. Flare the cable
outer conductor as shown.
3. Insert cable dielectric into rear body until it bottoms firmly against insulator
as shown.
4. Place a 0,38 (.015) dia. X 2,50 +/- 0,51 (.100 +/- .020) long solder wire into
solder hole of the center contact. Heat center contact and push it over cable
inner conductor until it bottoms against insulator as shown. Remove excess
solder if necessary.
5. Insert rear body into front body. Engage threads of retaining nut to front
body and hand tighten retaining nut. Hold front body firmly with a 7,93
(.312) hex. torque wrench and torque it to 1,13 - 1,69 Nm (10-15 in. lbs) by
turning retaining nut only.
6. Slide crimp ferrule over flared portion of cable outer conductor. Crimp outer
sleeve in place as shown. Push cable firmly toward connector when
crimping. Trim and remove any excess outer conductor strands if necessary.
Position shrink tubing over crimp sleeve apply indirect heat to shrink tubing
down.
Cable Numbers
RG142/U
RG316/U
RD316
Cable Code
9142
9188
9875
Die Size
5,41 (.213)
3,25 (.128)
3,84 (.151)
Die Set
K29265
K29263
T1025/9
A
13,46 (.530)
B
7,11 (.280)
C
3,56 (.140)
STEP 5
STEP 4
STEP 3
STEP 2
STEP 1
STEP 6
www.ittcannon.com
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
Cannon 50 Ohm Connectors ASSEMBLY INSTRUCTIONS
BBAAII--000011 SSMMBB // SSMMCC SSttrraaiigghhtt CCoonnnneeccttoorrss,, CCllaammpp TTyyppee ffoorr BBrraaiiddeedd CCaabbllee
CLAMP NUT No.1
WASHER
No.2
WASHER
GASKET SLEEVE REAR
INSULATOR
CONTACT FRONT
INSULATOR
FRONT
BODY
2,50
(.098)
3,50
(.138)
5,50
(.216)
1. Slide clamp nut, No.1 washer, gasket and No.2 washer over cable.
2. Trim cable to dimension shown taking care not to nick the braid.
3. Thumb braid out radially at right angles to dielectric.
4. A small chamfer may now be cut on the end of cable dielectric, to assist
assembly of sleeve.
5. Slide sleeve over cable dielectric and under braid and outer jacket until
the flange of the sleeve is flush against the braid.
6. Move No. 2 washer up to braid and trim braid flush with the flange of
the sleeve.
7. Trim cable dielectric and center conductor to dimensions shown taking
care not to nick the center conductor.
8. Tin center conductor (DO NOT OVER TIN).
9. Slide rear insulator over cable.
10. Place a small solder preform made from 0,26 - 0,31 (.010 - .012) dia (28
swg) multi-core sodler in rear of contact.
11. Push contact on center conductor as far as possible. Heat center
conductor and push until the shoulder of the contact is flush against the
rear insulator. Do not allow solder to protrude outside spill hole.
12. Slide on front insulator flush against rear insulator (if not already
assembled in body).
13. Move clamp nut, No.1 washer and gasket up to No. 2 washer, slide on
front body and tighten clamp nut to required torque: 0,63 - 0,70 Nm (90-
100 in. ozs.)
Only common cable retention features are shown in detail. V
arious body
configurations can apply
.
52
www
.ittcannon.com
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
STEP 9
STEP 7
STEP 5
STEP 3
STEP
2
STEP 1
STEP 13
STEP 12
STEP 11