ITT-Cannon-RF50-Catalog.pdf - 第57页
57 www .ittcannon.com Dimensions shown in mm (inch) Specifications and dimensions subject to change C C S S M M A A 5 5 - - S S M M A A R R i i g g h h t t A A n n g g l l e e C C o o n n n n e e c c t t o o r r s s , , …
56
www
.ittcannon.com
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
Cannon 50 Ohm Connectors ASSEMBLY INSTRUCTIONS
CCSSMMAA 44 -- SSMMAA SSttrraaiigghhtt CCoonnnneeccttoorrss,,
DDiirreecctt SSoollddeerr ((SSeeppaarraattee CCeenntteerr CCoonnttaacctt)) TTyyppee ffoorr SSeemmii--RRiiggiidd CCaabbllee
PLUG BODY INSULATOR CONTACT
SOLDER
A
B
1. Cut cable end square. Remove the cable outer conductor and
dielectric to the dimension shown taking care not to nick the center
conductor
. Deburr outer conductor at point of cut.
2. Tin center conductor. (DO NOT OVER TIN)
3. Solder contact to center conductor ensuring that the dimension
shown is maintained. Remove any excess solder.
4. Clean housing area of outer conductor with abrasive paper and clean
in a suitable agent.
5. Clamp the connector assembly in a suitable fixture. Ensure that the
contact is in the correct interface position. Place soldering ring
around cable adjacent to connector body and heat the connector
body using an appropriate heat source. Apply sufficient heat for
solder to flow but using minimum heat cycle.
6.
Using dielectric insertion T
ool T2508, press insulator into body
.
Assembly is now ready for use.
A
3.18 +/- 0.25 (.125 +/- .010)
B
0.38 (.015)
STEP 6
STEP 5
STEP 3
STEP 1
57
www.ittcannon.com
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
CCSSMMAA 55 -- SSMMAA RRiigghhtt AAnnggllee CCoonnnneeccttoorrss,,
DDiirreecctt SSoollddeerr TTyyppee ffoorr SSeemmii--RRiiggiidd CCaabbllee
BODY ASSEMBLY CAP
SOLDER
1. Remove cable outer conductor and dielectric to the dimension shown,
being careful not to fracture the center conductor. Tin center
conductor (DO NOT OVER TIN).
2.
Slide cable into body and solder into place.
3.
Solder center conductor to contact (do not over solder), then locate
the cap in rear of body and press flush to outer body to ensure it is
locked in position.
3.0
(.118)
Cannon 50 Ohm Connectors ASSEMBLY INSTRUCTIONS
STEP 3
STEP 2
STEP 1
Cannon 50 Ohm Connectors TOOLING
www
.ittcannon.com
Dimensions shown in mm (inch)
Specifications and dimensions subject to change
Centre Contact Crimp Tool
P
art Number
995-001-584
Ferrule Crimp Tool
Part Number
T1025 / -
Die Set for use with T1025 / -
Part Number
RG141/U
RG142/U
RG316
RD316
Cable Numbers
9141
9142
9188
9875
T
orque Wrench (for SMA coupling nut - mating)
Jaw Size
7.92 (.312)
T
orque Nm (in oz)
0.99 - 1.06 (140-150)
P
art Number
T0854/12/E
Die Size
5.42 (.213)
5.42 (.213)
3.25 (.128)
3.84 (.151)
Part Number
K29265
K29265
K29263 *
T1025/9
* Three way die set (illustrated)
Positioner for use with T4897
Part Number
T4898 for male contacts
T4899 for female contacts
58