ITT-Cannon-RF50-Catalog.pdf - 第64页

Customer Support Locations ASIA T uopandun Industrial Area, Jinda Cheng, Xiner Village, Shajing T own, Baoan District, Shenzhen City , Guangdong, China 518125 T el: +86 755 2726 7238 Fax: +86 755 2726 7515 GERMANY Cannon…

PRODUCT WARRANTY

www.ittcannon.com

Dimensions shown in mm (inch)

Specifications and dimensions subject to change

THIS NOTE MUST BE READ IN

CONJUNCTION WITH THE PRODUCT

DATA SHEET/CATALOG. FAILURE TO

OBSERVE THE ADVICE IN THIS

INFORMATION SHEET AND THE

OPERATING CONDITIONS SPECIFIED

IN THE PRODUCT DATA SHEET/

CATALOG COULD RESULT IN

HAZARDOUS SITUATIONS.

1. MATERIAL CONTENT AND

PHYSICAL FORM

Electrical connectors do not usually

contain hazardous materials. They

contain conducting and non-conducting

materials and can be divided into two

groups.

a) Printed circuit types and low cost audio

types which employ all plastic insulators

and casings.

b) Rugged, Fire Barrier and High

Reliability types with metal casings and

either natural rubber, synthetic rubber,

plastic or glass insulating materials.

Contact materials vary with type of

connector and also application and are

usually manufactured from either:

Copper, copper alloys, nickel, alumel,

chromel or steel. In special applications,

other alloys may be specified.

2. FIRE CHARACTERISTICS AND

ELECTRIC SHOCK HAZARD

There is no fire hazard when the

connector is correctly wired and used

within the specified parameters. Incorrect

wiring or assembly of the connector or

careless use of metal tools or conductive

fluids, or transit damage to any of the

component parts may cause electric

shock or burns. Live circuits must not be

broken by separating mated connectors

as this may cause arcing, ionization and

burning. Heat dissipation is greater at

maximum resistance in a circuit. Hot

spots may occur when resistance is

raised locally by damage, e.g. cracked or

deformed contacts, broken strands of

wire. Local overheating may also result

from the use of the incorrect application

tools or from poor quality soldering or

slack screw terminals. Overheating may

occur if the ratings in the product Data

Sheet/Catalog are exceeded and can

cause breakdown of insulation and hence

electric shock. If heating is allowed to

continue it intensifies by further

increasing the local resistance through

loss of temper of spring contacts,

formation of oxide film on contacts and

wires and leakage currents through

carbonization of insulation and tracking

paths. Fire can then result in the

presence of combustible materials and

this may release noxious fumes.

Overheating may not be visually

apparent. Burns may result from touching

overheated components.

3. HANDLING

Care must be taken to avoid damage

to any component parts of electrical

connectors during installation and use.

Although there are normally no sharp

edges, care must be taken when handling

certain components to avoid injury to

fingers. Electrical connectors may be

damaged in transit to the customers, and

damage may result in creation of

hazards. Products should therefore be

examined prior to installation/use and

rejected if found to be damaged.

4. DISPOSAL

Incineration of certain materials may

release noxious or even toxic fumes.

5. APPLICATION

Connectors with exposed contacts should

not be selected for use on the current

supply side of an electrical circuit,

because an electric shock could result

from touching exposed contacts on an

unmated connector. Voltages in excess of

30 V ac or 42.5 V dc are potentially

hazardous and care should be taken to

ensure that such voltages cannot be

transmitted in any way to exposed metal

parts of the connector body. The

connector and wiring should be checked,

before making live, to have no damage to

metal parts or insulators, no solder blobs,

loose strands, conducting lubricants,

swarf, or any other undesired conducting

particles. Circuit resistance and continuity

check should be made to make certain

that there are no high resistance joints or

spurious conducting paths. Always use

the correct application tools as specified

in the Data Sheet/Catalog. Do not permit

untrained personnel to wire, assemble or

tamper with connectors. For operation

voltage please see appropriate national

regulations.

IMPORTANT GENERAL INFORMATION

(i) Air and creepage paths/Operating

voltage. The admissible operating

voltages depend on the individual

applications and the valid national and

other applicable safety regulations.

For this reason the air and creepage path

data are only reference values. Observe

reduction of air and creepage paths due

to PC board and/or harnessing.

(ii) Temperature

All information given are temperature

limits. The operation temperature

depends on the individual application.

(iii) Other important information

Cannon continuously endeavors to

improve their products. Therefore,

Cannon products may deviate from the

description, technical data and shape as

shown in this catalog and data sheets.

“Engineered for life” is a registered

other trademarks or registered

trademarks are property of their

respective owners. All data subject to

change without notice.

Product Warranty

ITT Electronic Components, a Division

of ITT Corporation manufactures the

highest quality products available in

the marketplace; however these

products are intended to be used in

accordance with the specifications in

this publication. Any use or application

that deviates from the stated operating

specifications is not recommended and

may be unsafe. No information and

data contained in this publication shall

be construed to create any liability on

the part of Cannon. Any new issue of

this publication shall automatically

invalidate and supersede any and all

previous issues. A limited warranty

applies to Cannon products. Except for

obligations assumed by Cannon under

this warranty, Cannon shall not be

liable for any loss, damage, cost of

repairs, incidental or consequential

damages of any kind, whether or not

based on express or implied warranty,

contract, negligence or strict liability

arising in connection with the design,

manufacture, sale, use or repair of the

products. Product availability, prices

and delivery dates are exclusively

subject to our respective order

confirmation form; the same applies to

orders based on development samples

delivered. This publication is not to be

construed as an offer. It is intended

merely as an invitation to make an

offer. By this publication, Cannon does

not assume responsibility or any

liability for any patent infringements or

other rights of third parties which may

result from its use. Reprinting this

publication is generally permitted,

indicating the source. However,

Cannon's prior consent must be

obtained in all cases.

Customer Support Locations

ASIA

Tuopandun Industrial Area, Jinda Cheng,

Xiner Village, Shajing Town,

Baoan District, Shenzhen City,

Guangdong, China 518125

Tel: +86 755 2726 7238

Fax: +86 755 2726 7515

GERMANY

Cannonstrasse 1

Weinstadt, 71364

Tel: +49.7151.699.0

Fax: +49.7151.699.217

ITALY

Corso Europa 41/43

Lainate (MI),

Italy 20020

Tel: +39.02938721

Fax: +39.0293872300

Jays Close, Viables Estate

Basingstoke, Hants, RG22 4BA

Tel: +44.1256.311200

Fax: +44.1256.323356

USA

100 New Wood Road

Watertown, CT 06796

Tel: 860.945.0206

Toll Free: 800.683.7666

Fax: 860.645.0303

www.ittcannon.com

Corporation. Specification and other data are based on information available at the time of

printing, and are subject to change without notice.

ITT Cannon 50 RF Catalog 20170721

Cannon 50 Ohm

RF Connectors

Electronic Components