00193463-01.pdf - 第51页
User Manual SIPLACE S-25 HM 2 Operational Safety Software Vers ion SR.503.xx 04/2002 US Edition 2.1 Safety instruc tions 51 2 Operational Safety 2.1 Safety instructions 2.1.1 Conv ention s for the use of hazard symbols T…
1 Introduction, technical data User Manual SIPLACE S-25 HM
1.15 Overview of the modules - PCB conveyor Software Version SR.503.xx 04/2002 US Edition
50
User Manual SIPLACE S-25 HM 2 Operational Safety
Software Version SR.503.xx 04/2002 US Edition 2.1 Safety instructions
51
2 Operational Safety
2.1 Safety instructions
2.1.1 Conventions for the use of hazard symbols
This User Manual contains notes that must be observed to guarantee your personal safety and to
avoid damage to equipment. These notes are highlighted by warning triangles and are indicated
as follows according to the level of risk: 2
2
DANGER or 2
as used in this User Manual means that death, severe injury or considerable damage to equip-
ment will occur if the danger instructions are not followed. 2
2
WARNING or 2
as used in this User Manual means that death, severe injury or considerable damage to equip-
ment may occur if the warning instructions are not followed. 2
2
CAUTION or 2
as used in this User Manual means that slight injury or damage to equipment may occur if the cau-
tion instructions are not followed. 2
2
PLEASE NOTE 2
as used in this User Manual provides information on the product or indicates a part of the User
Manual that requires particular attention. 2
2.1.2 Qualified personnel
Qualified or adequately trained personnel means that these people are familiar with the setting up,
operation and maintenance of automatic placement systems and add-on devices and are suitably
qualified, e.g. 2
– have been trained, instructed or authorized to switch on and off, isolate, earth and identify elec-
trical circuits and system components in accordance with normal safety standards.
2 Operational Safety User Manual SIPLACE S-25 HM
2.1 Safety instructions Software Version SR.503.xx 04/2002 US Edition
52
– have been trained or instructed in the upkeep and use of appropriate safety equipment in ac-
cordance with normal safety standards.
– have received first aid training.
2.1.3 Use as prescribed
WARNING 2
The product must only be used for the applications specified in the catalogs and technical
descriptions, and then only in conjunction with non-SIEMENSDEMATIC devices and compo-
nents that have been recommended or approved by SIEMENSDEMATIC AG. For the product to
operate correctly and reliably, it must have been transported, stored, erected and assembled cor-
rectly and must be operated and maintained with care.
2.1.4 Important notes on operational safety
WARNING 2
The following points MUST be observed in order to maintain operational safety: 2
Æ NEVER open one of the protective covers if you are not totally familiar with the use and func-
tioning of the machine! Do not open the protective covers during operation unless you are told
to do so in this Manual or in the station software dialog.
Æ Only trained and qualified personnel may set the key switch to set-up mode ("I").
During operation, do not set the key switch to the "I" position (set-up mode) unless prompted
to do so in this manual or by the station software. 2
Æ NEVER place your head or arms in the gantry travelling range while the station is switched on!
Æ Never make changes, however minor, unless you are totally aware of the effect they will have
on the overall functioning of the system.
Æ The stations must always be set up, retooled and maintained by appropriately trained person-
nel.
Æ Only use SIEMENSDEMATIC original spare parts and authorized accessories. The use of
other parts will affect safety and may invalidate the liability for any consequential damage.
Æ The operational safety of SMD automatic placement systems can be guaranteed only if the
system is used as prescribed and in accordance with the instructions in the User/Service Man-
uals.