JO-072-006_w.pdf - 第108页

4-22 AKBEG-ID 2.1 Attachment and Detachment of Master T apes Reference Refer to the instruction manual of the tape feeders (for GXH series) for details. 2.1.1 Attachment of Master T ape(s) Procedure (1) While slightly pu…

4-21

AKBEG-ID

(22) Detach the master tapes rst, then the tape feeder from the jig. Now, the

measurement is completed.

To measure another feeder (same model) subsequently, follow the proce-

dures starting with the master tape setting described in (5).

To measure another feeder (different model), follow the procedures start-

ing with the program change described in (3).

CAUTION

If you detach the tape feeder with the master tapes

being attached from the jig, you may cut your nger

with sharp edges of the master tapes or damage the

tapes by bending the master tapes, etc.

Be sure to detach the master tapes rst, then the

tape feeder from the jig.

Reference

Refer to

2.1 Attachment and Detachment of Master Tapes

Section 4

for how to attach the master tapes.

0508-001

2. Feeder Measurement

4-22

AKBEG-ID

2.1 Attachment and Detachment of Master Tapes

Reference

Refer to the instruction manual of the tape feeders (for GXH series) for

details.

2.1.1 Attachment of Master Tape(s)

Procedure

(1) While slightly pushing down the suppressor end(s) of the tape feeder

with your nger, press the lower area of the end hook and lift up the

suppressor(s).

(2) Conrm that no foreign substances (chip components

, dirt, dust, etc.)

adheres to the chute surfaces and the underside(s) of the suppressor(s).

Notice

When the master tapes are attached with some foreign substances being

adhered, the suppressors and master tapes may be deformed, causing

an inaccurate measurement of the pickup position.

(3) Insert the master tape(s) from the end of the tape feeder as shown in the

photos below.

In the case of "8 mm Tape Feeder", insert the master tapes while slightly

pushing down the ends of the suppressors.

Suppressors Suppressor

1) Keep slightly pushing

the suppressors.

Insert the tape up to the first

curving portion of the chute.

2) Insert the tapes up to

the end of the tape

discharge guide.

For 8 mm Tape Feeder

For 12/16 mm or wider Tape Feeders

Fig. D27

(4) Attach the master tape(s) to the chute section so that the tape feed holes

can be engaged properly with the sprocket pins.

(5) Conrm that no foreign substances (chip components

, dirt, dust, etc.)

are scattered on the master tape(s).

(6) Slowly push down the suppressor(s).

0508-001

2.1 Attachment and Detachment of Master Tapes

4-23

AKBEG-ID

(7) Push down the upper area of the end hook with the suppressor(s) being

lowered and secure the suppressor(s).

GT-08080 GT-12160

Fig. D30 Tape Feeders Equipped with Master Tapes

2.1.2 Detachment of Master Tape(s)

Procedure

(1) While slightly pushing down the suppressor end(s) of the tape feeder

with your nger, press the lower area of the end hook and lift up the

suppressor(s).

(2) Pull out the master tape(s).

(3)

Slowly lower the suppressor(s).

(4) Push down the upper area of the end hook with the suppressor(s) being

lowered and secure the suppressor(s).

CAUTION

The master tapes are made of a thin metal. Carefully

handle the tapes to avoid cutting your nger with the

tape edges.

0508-001

2.1 Attachment and Detachment of Master Tapes