00197674-01-UM-E-Series-EN-12-2014.pdf - 第242页
5 Working with the machine User manual SIPLACE E 5.13 Changing the setup From software version SC 708.0 12/2014 E dition 242 5.13 Changing the setup 5.13.1 Printing out the setup list Print out the setup lis t on the pri…
User manual SIPLACE E 5 Working with the machine
From software version SC 708.0 12/2014 Edition 5.12 Observing displays on the SIPLACE SmartFeeder E
241
5
5
Red 24V supply voltage rose above the
switch-on threshold after switching
on and was then interrupted
Check the power supply
Red Tape feeder cycle did not end cor-
rectly within the specified time (tim-
eout for the "Feed" function)
Is the tape reel jammed in the container?
Is there a component jammed in the pick-up area be-
tween component tape and component window?
Once the obstacle has been eliminated, use the arrow
keys to restart the conveyor. The feeder module will
move the defective conveyor to the end, and then re-
turned to its position
Red Foil was not tensioned within the
specified time
The foil is probably torn. Insert new foil and tension
Red Foil was not peeled off even
though the tape is moved
The cover foil is probably jammed beneath the pick-up
window and cannot be peeled off correctly
Red Foil motor has locked up Leveling gears blocked by foil? => Remove the foil
Red The data back-up in the EEPROM
was not carried out correctly
Remove the component tape (tape can be moved out by
pressing the arrow keys or pulled out after raising the
pick-up window). Press the SET button to confirm the
error. Then press the yellow button to confirm the refer-
ence run prompt.
Red Data was not read from the EE-
PROM correctly
Red The data back-up in the EEPROM
was not carried out fully
Red Position information is no longer
available for the component tape
drive
Remove the component tape (tape can be moved out by
pressing the arrow keys or pulled out after raising the
pick-up window). Then press the "FOIL" button to start
the reference run.
Red CAN bus error Log off and on again, check the optical fiber interface
Red Parameters were not saved Default parameters are loaded automatically, i.e. the
most recent operator settings are overwritten -> The
settings (e.g. increment) will have to be made again.
Replace the control board if this error occurs frequently.
Red Wrong or incomplete parameters
were saved
Red Can no longer write to boot or ap-
plication memory correctly
Replace the feeder module or control board
Status
display
Possible Meaning Solution
PLEASE NOTE
Remove the component tape before a reference run.
5 Working with the machine User manual SIPLACE E
5.13 Changing the setup From software version SC 708.0 12/2014 Edition
242
5.13 Changing the setup
5.13.1 Printing out the setup list
Print out the setup list on the printer for the SIPLACE Station Programming. Go to Job Editor =>
Edit job => Optimizer => Actions => Export setup list.
5.13.2 What you should note when changing the feeder modules
Handle the feeder modules carefully when you insert them into or remove them from the
changeover table. Make sure that the SIPLACE SmartFeeder E do not bump against the cen-
tering bar (see item 5 in fig. 5.11 - 3, page 233) of the changeover table.
Vacuum the supporting surfaces of the feeder modules and clean the surface of the change-
over table when necessary.
5
Remove loose components using a brush or a vacuum cleaner with a suitable nozzle.
5
CAUTION
Risk of injuries!
Fine metal splinters from components could injure hands.
Avoid removing components from the changeover table with your fingers.
User manual SIPLACE E 5 Working with the machine
From software version SC 708.0 12/2014 Edition 5.14 Avoiding track errors
243
5.14 Avoiding track errors
5.14.1 General
Make sure that the areas around the feeder modules are clean and that there are no loose
components in the feeder area or under the feeder modules.
Refill promptly with components.
Splice the tapes early. This generally means that you are to prepare the splicing material
when there is still approximately 1.5 m of tape on the reel.
Handle the feeder modules carefully when you insert them into or remove them from the
changeover table as these are high-precision devices.
For SIPLACE SmartFeeder E, lower the pickup window since it can easily be damaged when
raised.
5
Check that the pick-up position is set correctly for the components on the feeder modules.
5.14.2 Avoiding track errors with the tape container
Insert the separating plates correctly (see fig. 5.10 - 2, page 228).
PLEASE NOTE
A raised pick-up window leads to noticeably impaired pick-up quality.