Nordson_EFD_OptiSure_Operating_Manual.pdf - 第70页

OptiSure Automated Optical Inspection 70 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide. OptiSur eAOI Kit Part Numbers Nordson EFD’s Op…

OptiSure Automated Optical Inspection

69www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.

Using the Laser to Measure and Record Profiles

(continued)

System Responses for Laser Threshold Measurement Checks

Action Reference Image

When SKIP is selected:

• If a measurement is outside a Max or Min

value, the program stops running after the

laser measurement is done and then prompts

to go to the HOME position. When this

occurs, click HOME.

When STOP is selected:

• If a measurement is below the Min value,

the program stops running and the system

generates a Surface Detect Fail warning.

When this occurs, click OK and then click

HOME.

• If a measured value is above the Max value,

the program stops running and the system

prompts to go to the HOME position. When

this occurs, click HOME.

When PAUSE is selected:

If a measurement is outside a Max or Min value,

the program stops running:

• Select CONTINUE to continue

running the program.

• Select STOP to stop the program,

then click HOME to return the robot to the

HOME position.

OptiSure Automated Optical Inspection

70 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.

OptiSureAOI Kit Part Numbers

Nordson EFD’s OptiSure Automated Optical Inspection (AOI) software is available within the current DispenseMotion

software as an optional add-on. The AOI feature inspects ﬂuid deposit widths and diameters with exceptional

certainty and determines if dispense requirements have been met. When paired with the OptiSureAOI confocal

laser, the AOI feature provides three-dimensional (3D) deposit veriﬁcation by measuring the height, width, and

diameter of a ﬂuid deposit and comparing it to a 3D image of a desired deposit to determine true volume accuracy.

The OptiSureAOI feature also includes advanced functions for augmenting mark images to make them easier for

the system ﬁnd.

Item Part # Description

7365229 Software key, OptiSure Automated Optical Inspection (AOI)

7364992

Laser C accessory kit (includes the confocal laser and laser controller)

NOTES:

• For use only with the OptiSure AOI add-on

• Includes the OptiSure AOI software key

• Takes the place of Laser A or Laser B

OptiSure Automated Optical Inspection

71www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.

AppendixA, Command Function Reference

This appendix provides detailed information for each setup and dispense command. Commands are in alphabetical

order.

The following rules apply to all commands:

• A command is in effect until it is superseded by another command.

• Command settings override system settings.

Arrow Check Point

Click Function

Double-click

address and

select from drop-

down menu

Used in tandem with the Mea. Width, Mea. Point to Line, and Positional Checking options of the

OptiSureAOI feature to check the width of a section of a dispensed line (between two speciﬁed points)

against a saved mark image that can specify Max and Min parameters for line width; if the width of a section

of dispensed line is not within the allowable range, the system takes the action speciﬁed by the Skip, Stop,

Pause, or Ask parameter.

Parameter Description

No. The number of the mark image saved for the line section.

0.Stop, 1.Skip,

2.Pause, 3.Ask

The action the system takes if a dispensed line section does not meet the parameters

speciﬁed for the saved mark image.

0.Stop The system stops running the program and displays an Arrow Check Fail

warning: Click OK to acknowledge the warning, then click HOME to move the

Zaxis to the Home position (0, 0, 0).

1.Skip The system skips the dispense and goes to the next command in the program.

2.Pause The system stops running the program and displays a “Waiting [Start] Button]”

box: Click START or CONTINUE to continue running the program; click STOP

and then HOME to stop the program and send the robot to the Home position

(0, 0, 0).

3.Ask The system stops running the program and displays a “Find Again, Find Next,

or Stop Find” box: Click FIND AGAIN to make the system check the point

again. Click FIND NEXT to go to the next command in the program. Click STOP

FIND to stop the program.