PC200_Manual_REV_G-1.pdf - 第54页
PC200 PVA Revis ion G (201 9) 54 of 56 Warranty PVA Warr anty Policy PVA war rants the enclo sed product against defects in material or work manship on all componen ts for o ne year fr om the date of ship ment. The warr …
PC200
PVA
Revision G (2019)
53 of 56
Notes
PC200
PVA
Revision G (2019)
54 of 56
Warranty
PVA Warranty Policy
PVA warrants the enclosed product against defects in material or workmanship on all
components for one year from the date of shipment.
The warranty does not extend to components damaged due to misuse, negligence, or
installation and operation that are not in accordance with the recommended factory
instructions. Unauthorized repair or modification of the enclosed product, and/or the
use of spare parts not directly obtained from PVA (or from factory authorized dealers)
will void all warranties.
All PVA warranties extend only to the original purchaser. Third party warranty claims
will not be honored at any time.
Prior to returning a product for a warranty claim, a return authorization must be
obtained from PVA’s customer service department. Authorization will be issued either
via the telephone, facsimile, or in writing upon your request.
To qualify as a valid warranty claim, the defective product must be returned to the
factory during the warranty period. Upon return, PVA will repair (or replace) all
components found to be defective in material or workmanship.
(Retain this for your records)
Product Information:
PRODUCT: ______________________________
SERIAL NUMBER: ______________________________
DATE OF PURCHASE: ______________________________
PC200
PVA
Revision G (2019)
55 of 56
Table of Figures
Figure 1: General PC200 Pneumatic Schematic .................................................................. 7
Figure 2: Valve Components ............................................................................................... 9
Figure 3: Static Mixer ........................................................................................................ 11
Figure 4: Fill the Static Mixer ............................................................................................ 11
Figure 5: Purge the Static Mixer ....................................................................................... 12
Figure 6: PC200 Night Cap ................................................................................................ 13
Figure 7: PC200 Ready for Disassembly ............................................................................ 14
Figure 8: Fluid Manifold Screws ........................................................................................ 14
Figure 9: Disassembled Fluid Manifold ............................................................................. 15
Figure 10: Valve Shoulder Bolts ........................................................................................ 15
Figure 11: Remove Air Cap Screws ................................................................................... 15
Figure 12: Air Cylinder without Air Cap ............................................................................ 16
Figure 13: Remove Air Fittings .......................................................................................... 16
Figure 14: Push Rods to Disengage ................................................................................... 16
Figure 15: Disengaged Piston-Rod Assembly .................................................................... 17
Figure 16: Seal Plate Removed ......................................................................................... 17
Figure 17: Piston-Rod Assembly Removed ....................................................................... 17
Figure 18: Disconnect Valve Sections ............................................................................... 18
Figure 19: Install the Tap into the Sleeve Bearing ............................................................ 18
Figure 20: Engage the Tap into the Sleeve Bearing .......................................................... 18
Figure 21: Turn the Tap and Pull Out ................................................................................ 19
Figure 22: Remove the Sleeve Bearing ............................................................................. 19
Figure 23: Remove Lip Seals From Fluid Section .............................................................. 20
Figure 24: Air Cylinder O-ring............................................................................................ 20
Figure 25: Clean the Seal Plate ......................................................................................... 21
Figure 26: Clean the Air Cylinder ...................................................................................... 21
Figure 27: Clean the Cylinder Cap ..................................................................................... 21
Figure 28: Clean the Fluid Section .................................................................................... 22
Figure 29: Clean the Piston-Rod Assembly ....................................................................... 22
Figure 30: Install Screw in the Piston-Rod Assembly ........................................................ 23
Figure 31: Rods and Piston................................................................................................ 23
Figure 32: Tighten Rods .................................................................................................... 24
Figure 33: Put the O-ring on the Piston ............................................................................ 24
Figure 34: Sleeve Bearings Installed in the Separation Block ........................................... 24
Figure 35: Lip Seals in Seal Plate ....................................................................................... 25
Figure 36: Lip Seal Alignment Tool and Fluid Section ....................................................... 25
Figure 37: Lip Seal Insertion Tool ...................................................................................... 25
Figure 38: O-rings for the Fluid Section ............................................................................ 26
Figure 39: Align the Sections ............................................................................................. 26