SC_450 PreciseCoat Conformal Coating Jet_Rev_04.pdf - 第9页

© 2024 Nordson Corporation 3 2 Safety 2.1 Overview This section is int ended to provide basic saf ety information ne cessary for operati ng and ser vicing the SC-450 Prec iseCoat Jet. This sectio n covers the following t…

SC-450 PreciseCoat Conformal Coating Jet Introduction

1.3 Dimensions

Figure 1-1 SC-450 PreciseCoat Jet Dimensions

2 Safety

2.1 Overview

This section is intended to provide basic safety information necessary for operating and servicing the

SC-450 PreciseCoat Jet. This section covers the following topics:

•

Safety First

•

Disposal

•

Equipment Use

•

Emergency Shutdown

• Basic Safety Precautions and

Practices

• Safety Warning Labels

•

Decommis

sioning

To further optimize safe operation, precautions and recommended practices are included with the

procedures throughout this manual.

WARNING!

Failure to comply with any of the safety recommendations could cause serious

injury to the user or damage to the coating system.

NOTE

Safety is considered a joint responsibility between the original equipment

manufacturer (Nordson) and the end-user (owner). All safety precautions and

practices should be in accordance with local regulations and facility policy.

2.2 Safety First

Coating system operation involves air pressure, fluid pressure, mechanical and pneumatic devices,

electrical power, and the use of hazardous materials, and sometimes may involve heat. In addition to the

safety precautions listed in this manual, refer to the safety section in the applicable coating system

Installation, Operations, and Maintenance Manual prior to installing and operating the Select Coat

applicator.

2.3 Equipment Use

2.3.1 Intended Use

Use of Nordson equipment in ways other than those described in the documentation supplied with the

equipment may result in injury to persons or damage to property. Some examples of misuse include:

• Using incompatible materials

• Making unauthorized modifications

• Removing or bypassing safety guards or interlocks

• Using incompatible or damaged parts

• Using unapproved auxiliary equipment

• Operating equipment in excess of maximum ratings

SC-450 PreciseCoat Conformal Coating Jet Safety

2.4 Basic Safety Precautions and Practices

Compliance with the following recommended precautions and practices will prevent personal injury or

damage to property during applicator operation and maintenance.

WARNING!

Failure to comply with any of the safety recommendations could cause serious

injury to the user or damage to the coating system.

2.4.1 Safety of Personnel

• Only trained personnel should be permitted to perform operation, maintenance, and

troubleshooting procedures on the SC-450 PreciseCoat Jet.

• There should always be a second person present when performing maintenance on the

coating system that is powered up.

• Before performing maintenance or service on the SC-450 PreciseCoat Jet, position the

applicator at the front of the coating chamber. This will provide easy access to components

and limit exposure to hazardous areas.

• Immediately push the red Emergency Machine Off (EMO) button on the coating system if

personnel are in danger.

• Do not wear loose clothing or jewelry while operating the system. Tie back long hair to

prevent it from being caught in moving parts.

• Do not touch moving parts while the coating system is operating.

• To prevent burn injury, wear thermal gloves when working around heater tooling and fluid

heaters.

• Make sure all facility power sources are safely grounded.

• Routinely inspect all air hoses and electrical cables for damage.

• Make sure power cords and air supply hoses do not cross a walkway or aisle.

• Maintain a clean and orderly work area.

• Remove the SC-450 PreciseCoat Jet completely from the coating system before cleaning or

performing maintenance.

• Relieve pneumatic pressure before adjusting or servicing pressurized components.

2.4.2 Material Safety

• Follow Safety Data Sheet (SDS) recommendations for the proper handling, cleanup, and

disposal of hazardous materials and fluids and their containers (i.e., syringes, cups,

reservoirs, etc.) used with the coating system.

• Know the SDS recommendations for treatment of injury resulting from exposure to

hazardous materials.

• Make sure the coating system ventilation is ON during handling and cleanup of all materials

used with the coating system.

• Obtain the SDS from the applicable chemical supplier for chemical substances not provided

with the equipment. These chemical substances include those used for processing,

maintenance, and service of the equipment.

• Always wear appropriate Personal Protective Equipment (PPE) as recommended by facility

safety practices and the material manufacturer’s SDS.