00196378-0102_UM X-Feeder_EN.pdf - 第21页

Overview of X Feeder Modules Structure of the SIPLACE X-Series Tape Feeder Modules Functions and Operating Controls User Manual X Feeder M odules SIPLACE Family 21 8 mm X tape feeder module - rear view Legend (1) Entry t…

Overview of X Feeder Modules

Functions and Operating Controls Structure of the SIPLACE X-Series Tape Feeder Modules

20 User Manual X Feeder Modules SIPLACE Family

8 mm X tape feeder module - front view

Legend

(1) Locking roll for fixing the feeder mod-

ule on the component table

(2) EDIF (energy and data interface)

(3) Front centering pin (4) Lever for raising the pickup window in

order to thread in and remove the

component tape

(5) Pickup window (6) Exit from the empty tape duct

(7) Setting of the foil tension (8) Foil rocker

(9) Tape disposal rolls (10) Rear centering pin

(11) Type plate

Overview of X Feeder Modules

Structure of the SIPLACE X-Series Tape Feeder Modules Functions and Operating Controls

User Manual X Feeder Modules SIPLACE Family 21

8 mm X tape feeder module - rear view

Legend

(1) Entry to the empty tape duct with tape

spring

(2) Removal flap to the foil container

(3) Integrated blade for cutting off the

cover foil

(4) Removal handle, engaged

(5) Operator panel (6) Drive motor for foil removal

(7) Drive motors for the tape conveyor (8) Rotary valve for removing compo-

nents

(9) Front sliding guide (10) Rear sliding guide

(11) Graphical representation of the pick-

up position in relation to the compo-

nent size

Overview of X Feeder Modules

Functions and Operating Controls Display at the Tape Feeder Modules

22 User Manual X Feeder Modules SIPLACE Family

3.1.2 Display at the Tape Feeder Modules

3.1.2.1 LED Display on the 2x8 mm Tape Feeder Modules

Status display

▪ If the status display lights up green, the respective track of the feeder module is ready-to-operate

and needed for the current placement job. This status display also lights up green, if no placement

job has been assigned yet.

▪ If the status display is orange, this indicates that a warning has been issued.

▪ If the status display lights up red, an error has occurred. In the case, the pitch display indicates the

error source.

▪ If the status display remains dark, the feeder module is not needed for the current placement job.

Definitions of Terms Describing the Operating and Display Functions

Operator panel of the 2x8 mm tape feeder modules

Legend

1. Pitch display (LEDs) right

2. Track display right

3. Track change button

4. Forwards button

5. Backwards button

6. Foil button

7. Set button

8. Status display (2x)

9. Track display left

10. Pitch display (LEDs) left

The X feeder modules are equipped with 10 LEDs

(1, 2, 9 and 10) for indicating the operating states and

one multi-colored status display for each track (8).

Display The display indicates a specific status (e. g. the currently set pitch or the se-

lected track) and consists of several LEDs.

LED Abbreviation for "light emitting diode". LED designates a single element in a

display (e. g. left track "L").

Short press of the button The button is pressed and released within 0.75 seconds.

Long press of the button The button is being pressed more than 0.75 seconds.

Fast flashing

The LED is on and off for 0.15 second each, i. e., it flashes 3.3 times per

second.

Slow flashing

The LED is on and off for 0.45 second each, i. e., it flashes approx. once per

second.

Running light forwards The LEDs 1, 2, 4 and 8 of the pitch display light up one after another and

then they are all off. After that this sequence is repeated.

Running light backwards The LEDs 8, 4, 2 and 1 of the pitch display light up one after another and

then they are all off. After that this sequence is repeated.