00196378-0102_UM X-Feeder_EN.pdf - 第92页
Messages Messages for 8 - 88 mm Feeder Modules Messages From Process 92 User Manual X Feeder Modules SIPLACE Family 5.2.2.14 Location Error 5.2.2.15 Foil Tension LCD, de: LCD, en: Place Fehler Place error Status display:…
Messages
Messages From Process Messages for 8 - 88 mm Feeder Modules
User Manual X Feeder Modules SIPLACE Family 91
5.2.2.9 Pickup Error
5.2.2.10 Target Directory Full
5.2.2.11 External Deactivation
5.2.2.12 Refill
5.2.2.13 Wrong Type
LCD, de:
LCD, en:
Abhol Fehler
Pickup Error
Status display:
Cause: The component on this track was not correctly picked up by the placement head.
The track was disabled.
Solution: Check the nozzle vacuum.
Comments: This requires an exact analysis of the pickup process, as this error message could
have several causes.
LCD, de:
LCD, en:
Verz. Voll
Target Full
Status display:
Cause: The data folder (spool), for an external operating data recording system, is full.
Unable to save Traceability or GEM data.
Solution: This message can only be reset in the external system (HOST).
Comments: - - -
LCD, de:
LCD, en:
Extern Deak.
Extern Deac.
Status display:
Cause: The track was disabled externally (e.g. through setup verification).
Solution: The track needs to be re-enabled by the external system.
Comments: - - -
LCD, de:
LCD, en:
Nachfuellen
Refill
Status display:
Cause: The track has been disabled because a deactivation threshold was reached.
Solution: Splice on new components for the relevant track (refill trays) and set the track to
"full".
Comments: A warning threshold has been exceeded e.g. by the level checker.
LCD, de:
LCD, en:
Falscher Typ
Wrong Type
Status display:
Cause: A different feeder module type is set in the programming system to that set in the
machine.
Solution: Correct the feeder module type or change the current setup in the programming
system.
Comments: The machine can recognize a feeder module at the location. However, this does
not match that specified in the current setup.
Messages
Messages for 8 - 88 mm Feeder Modules Messages From Process
92 User Manual X Feeder Modules SIPLACE Family
5.2.2.14 Location Error
5.2.2.15 Foil Tension
LCD, de:
LCD, en:
Place Fehler
Place error
Status display:
Cause: The feeder module has not been placed in position or communication to the feeder
module does not function properly.
Solution: Set the feeder module up according to the programming system requirements.
Check the interface to the FCU (EDIF).
Comments: The machine is unable to recognize the feeder module.
LCD, de:
LCD, en:
Folienspann.
Foil Tension
Status display:
Cause: Foil tension is too low.
Solution: Insert the tape and tension the foil.
Comments: - - -
Accessories
Linear Dipping Unit X (LDU X)
User Manual X Feeder Modules SIPLACE Family 93
6 Accessories
6.1 Linear Dipping Unit X (LDU X)
Description
The Linear Dipping Unit X is used for covering flip chips and CSP components with flux material. The
flux container glides in a linear movement over the dipping plate and applies the flux with a defined layer
thickness into the cavity of the dipping plate. The parameters for covering a component with flux are
specified in SIPLACE Pro. After the component has been covered, the flux layer is renewed. This
process guarantees equal process conditions for the components.
The display field shows the individual menus for actions and operating parameters. Using the buttons of
the operator field you can select the menus or modify and save parameters. The 4 LEDs of the display
field indicate the status of the LDU-X. Use the EMERGENCY OFF button to switch off the LDU-X imme-
diately.
The LDU-X is suitable for the following placement heads:
▪ 6-segment Collect&Place head
▪ 12-segment Collect&Place head
▪ TwinHead
The LDU-X is considered as a separate feeder module type in the setup. The module can only be set up
on component tables of the SIPLACE X series. An implemented warming up function allows to change
the viscosity of the flux material. For testing purposes the LDU-X can be operated outside the machine
by means of the energy and data interface for X feeder modules.
For further information on the LDU-X, please refer to the operating manual supplied with the module.
Linear dipping unit (LDU X)
Item no. 00117011-xx
Legend
1. LDU X
2. Dipping plate
3. Flux tank
4. Display field (4 lines with 20 characters each)
5. Operator panel with 6 foil buttons
6. LED for status displays
7. EMERGENCY STOP button