00196378-0102_UM X-Feeder_EN.pdf - 第90页

Messages Messages for 8 - 88 mm Feeder Modules Messages From Process 90 User Manual X Feeder Modules SIPLACE Family 5.2.2.4 Scan OK 5.2.2.5 Scan Error 5.2.2.6 Fill level Too Low 5.2.2.7 Splice Sensor 5.2.2.8 Vision Error…

Messages

Messages From Process Messages for 8 - 88 mm Feeder Modules

User Manual X Feeder Modules SIPLACE Family 89

5.2.1.26 EEPROM Data Error

5.2.1.27 Scan Request

5.2.2 Messages From Process

5.2.2.1 Introduction

The following messages are only shown by the feeder module. The display text itself is generated by the

station computer and is then transmitted via the CAN bus to the LCD display of the feeder module. The

error source is therefore not in the feeder module but usually in the placement machine state. For exam-

ple, pickup or Vision errors, which affect the component of a particular track, will be displayed on the

feeder module for that track. The following table shows the LCD display text, the color and mode of the

status display, the cause and troubleshooting measures.

5.2.2.2 Not Verified

5.2.2.3 Scan Barcode

LCD, de:

LCD, en:

EEP-DataErr

Status display: red

Cause: The data back-up in the EEPROM was not carried out completely

Solution: Remove the tape. Acknowledge the error with the SET button. Acknowledge the

prompt for a reference run with the yellow button.

If the message continues to appear, you will need to replace the control board or

the drive.

Comments: Since the position of the drive is stored in the EEPROM, a reference run is

necessary in these cases.

LCD, de:

LCD, en:

Scan Anford.

Scan Request

Status display: - - -

Cause: The request to perform scanning has been sent by the feeder module to the MC

(Machine Controller).

Solution: - - -

Comments: After the grey SET button has been pressed (1 sec.) the display shows the

Scan Anford. / Scan Request message for approx. 2 sec. to indicate that

the feeder module has sent a request for barcode scanning to the MC. If a barcode

system is active, the MC will then send the Scan Barcode display text to the

feeder module.

From version 1.24

LCD, de:

LCD, en:

NichtGeprueft

Not verified

Status display:

Cause: The tape has been inserted but the barcode has not yet been scanned.

Solution: Scan the barcode.

Comments: This message is only shown if a barcode system has been installed and is active.

LCD, de:

LCD, en:

Scan Barcode

Status display:

Cause: The barcode still needs to be scanned.

Solution: Scan the barcode.

Comments: - - -

Messages

Messages for 8 - 88 mm Feeder Modules Messages From Process

90 User Manual X Feeder Modules SIPLACE Family

5.2.2.4 Scan OK

5.2.2.5 Scan Error

5.2.2.6 Fill level Too Low

5.2.2.7 Splice Sensor

5.2.2.8 Vision Error

LCD, de:

LCD, en:

Scan OK

Status display:

Cause: Barcode scanning was successful.

Solution: - - -

Comments: - - -

LCD, de:

LCD, en:

Scan Fehler

Scan Not OK

Status display:

Cause: Barcode scanning was not successful.

Solution: Scan the barcode again.

Comments: Check the quality of the barcode label.

LCD, de:

LCD, en:

Fuell. Niedrig

Low Filling

Status display:

Cause: Warning issued when fill level is too low

Solution: Splice on new component reel and update fill level.

Comments: This message is only shown if a component level indicator has been installed and

is active.

LCD, de:

LCD, en:

SpleissSensor

SpliceSensor

Status display:

Cause: Warning issued when the splice sensor is missing.

Solution: Provide a feeder module with splice sensor or switch off the component level indi-

cator in the station software, if this is not being used.

Comments: The splice sensor in a feeder module is only required by the placement machine if

a component on this track is subject to a component level indicator or traceability

function.

LCD, de:

LCD, en:

VisionFehler

Vision Error

Status display:

Cause: The component on this track has not been correctly recognized by the image

processing tool or the component is defective.

Solution: Check the geometry of the component with the Vision data

Comments: This requires an exact analysis of the pickup process, as this error message could

have several causes.

Messages

Messages From Process Messages for 8 - 88 mm Feeder Modules

User Manual X Feeder Modules SIPLACE Family 91

5.2.2.9 Pickup Error

5.2.2.10 Target Directory Full

5.2.2.11 External Deactivation

5.2.2.12 Refill

5.2.2.13 Wrong Type

LCD, de:

LCD, en:

Abhol Fehler

Pickup Error

Status display:

Cause: The component on this track was not correctly picked up by the placement head.

The track was disabled.

Solution: Check the nozzle vacuum.

Comments: This requires an exact analysis of the pickup process, as this error message could

have several causes.

LCD, de:

LCD, en:

Verz. Voll

Target Full

Status display:

Cause: The data folder (spool), for an external operating data recording system, is full.

Unable to save Traceability or GEM data.

Solution: This message can only be reset in the external system (HOST).

Comments: - - -

LCD, de:

LCD, en:

Extern Deak.

Extern Deac.

Status display:

Cause: The track was disabled externally (e.g. through setup verification).

Solution: The track needs to be re-enabled by the external system.

Comments: - - -

LCD, de:

LCD, en:

Nachfuellen

Refill

Status display:

Cause: The track has been disabled because a deactivation threshold was reached.

Solution: Splice on new components for the relevant track (refill trays) and set the track to

"full".

Comments: A warning threshold has been exceeded e.g. by the level checker.

LCD, de:

LCD, en:

Falscher Typ

Wrong Type

Status display:

Cause: A different feeder module type is set in the programming system to that set in the

machine.

Solution: Correct the feeder module type or change the current setup in the programming

system.

Comments: The machine can recognize a feeder module at the location. However, this does

not match that specified in the current setup.