00196378-0102_UM X-Feeder_EN.pdf - 第97页

Accessories Area of Use Tape Splicing Tool for SMD Tape Connections User Manual X Feeder M odules SIPLACE Family 97 6.4 Tape Splicing Tool for SMD Tape Connections 6.4.1 Area of Use The splice tool enables you to splice …

100%1 / 108
Accessories
Energy and Data Interface (Single Slot EDIF) for X Feeder Modules Description
96 User Manual X Feeder Modules SIPLACE Family
6.3 Energy and Data Interface (Single Slot EDIF) for X Feeder
Modules
6.3.1 Description
By means of the energy and data interface X feeder modules can be put into operation outside the
machine and the pre-setup location. The interface consists of an Omega profile for taking in and guiding
the feeder modules. Like on the component trolley the feeder module is placed on the Omega profile
with its sliding guides and pushed forwards until the front centering pin completely immerges into the
hole. The locking latch locks the feeder module in this position.
For removing the feeder module press the unlocking button. The locking latch is pressed down and
releases the feeder module. Foldout feet stabilize the position of the energy and data interface, namely
for broad feeder modules.
The electronic housing contains the control electronic for the energy and data interface. The operator
panel consists of a start and and stop button as well as two LEDs for the status display. Communication
with the PC is carried out via the data cable. The power supply cable is connected to the power supply
which is contained in the scope of delivery.
6.3.2 Usage
The energy and data interface is used for checking, maintaining and repairing X feeder modules. In
addition, it can be used for offline setups in the PCB production. For this purpose, the energy and data
interface is fitted on the base plate. The reel holder is also mounted to the base plate. When the compo-
nent tape is inserted you can either check or change the values for pitch, pickup position and transport
speed.
A detailed operating manual describes the handling of the interface and the corresponding service
works.
6.3.3 Scope of Delivery
▪ Single Slot EDIF
▪ Power supply, 100 - 120 / 200 - 240 V~, +30 V-, 4.3 A
▪ Base plate with reel arm
▪ Operating manual
Energy and data interface for X feeder modules
Item no. 00141247-xx
Legend
1. Unlocking button for releasing the locking latch
2. Operator panel
3. Data cable
4. Power supply cable
5. Electronic housing
6. Foldout feet
7. Omega profile for guiding the feeder modules
8. Locking latch
9. Hole for the front centering pin of the feeder module
10. Base plate
11. Reel holder
Accessories
Area of Use Tape Splicing Tool for SMD Tape Connections
User Manual X Feeder Modules SIPLACE Family 97
6.4 Tape Splicing Tool for SMD Tape Connections
6.4.1 Area of Use
The splice tool enables you to splice on a new tape for refilling components on tapes without causing a
machine standstill.
The splicing procedure takes place outside the working area of the SIPLACE placement machine which
is secured with protective switches.
When splicing components on tapes, you connect the virtually finished paper or blister tape in the feeder
with the beginning of a new tape.
The splice tool functions like a crimping tool. It enables you to "rivet" the underside of the tape, thereby
connecting the "old" and "new" tapes with one another. A special adhesive strip on the upper side of the
tape connects the cover foil.
When correctly connected, the tape ends are joined together precisely to the grid. The tape - with its
transition point - can then be seamlessly transported into the feeder and the foil can be stripped off as
usual.
The splice tool can be used to splice all blister or paper tapes.
Tapes WITHOUT cover foil (surf tapes) are NOT spliced together.
Item No. 02102987-xx
NOTICE! A description of how to splice tapes is
also available as a poster for your production site: Job
Poster "", Item No. 00192460-xx
Splicing tapes
Splice tool and complete splicing of paper and blister
tapes (with single-sided and double-sided perforations
Legend
1. Splice tool
2. 8 mm paper tape
3. Blister tapes with perforations on one side
4. Blister tape with perforations on both sides
5. Complete SMD tape splicing
NOTICE! The splice tool can be used easily by
both right and left-handed persons.
Accessories
Tape Splicing Tool for SMD Tape Connections Safety Instructions
98 User Manual X Feeder Modules SIPLACE Family
6.4.2 Safety Instructions
6.4.3 Tools Required
Tools
▪ Splice tool
▪ Splice tool, Item No. 02102987-xx (optional, without consumable materials package)
▪ Scissors for paper, sharp but not too long or pointed
▪ Pointed tweezers
▪ You may need a brush with shirt, firm bristles to clean the contact surface of the feeder on the
changeover table.
6.4.4 Consumable Materials Required
The following consumable materials are contained in the "Consumables package for splice tool", Item
No. 02102988-03:
▪ Special adhesive tape, width 8 mm
(Item No. for separate orders 00356343-xx)
▪ Splicing plates, suitable for all tapes used with SIPLACE placement machines, which can be
"refilled" by splicing!
(Item No. for separate orders 00318671-xx)
Not included in the above mentioned consumable materials package:
▪ Special adhesive tape, width 16 mm, Item No. 00356344-xx
WARNING
When closing the splicing tool, hold it away from your body and make sure that you do not get
your fingers near the closing apparatus.
CAUTION
The splice tool is only used outside the placement machine.
Make sure that no parts, such as the riveted strips or pieces of adhesive tape, can fall into the
feeder or the working area of the placement machine, as this could interrupt operation and
cause malfunctions.
NOTICE
To splice tapes, you require the
SIPLACE Operator Kit
,
Item No. 00349303-xx.
This Operator Kit contains 1 leather case, 1 pair SMD tweezers, 1 small slotted screwdriver,
1 small Phillips screwdriver, 1 pair scissors and 1 brush.
CAUTION
Make sure that you ONLY use the special adhesive tapes specified here for splicing.
NEVER use other adhesive tapes, such as normal sellotape!